Most boilers come with a manufacturer’s warranty. But after a few years, we experience some common boiler problems. Such problems can be addressed without the need to call a heating engineer; others will require the services of a qualified and experienced professional.

If the boiler feed water contains impurities beyond the prescribed limits they lead to the following problems.

1. (a) priming (b) foaming (c) carry over
2. Boiler corrosion
3. Scale sludge and formation
4. Caustic embitterment

1. Priming Foaming and Carry Over: when steam is produced rapidly in the boiler some small droplets of the liquid water are carried along with the steam. The steam with some small water droplets is called “wet steam “.
(a) Priming: The process of formation of wet steam is called priming. Priming also starts when level of water rises due to foaming. So priming is generally associated with foaming.
(b) Foaming: The formation of foam or bubbles at the water surface in boilers is called foaming which does not break easily.
(c) Carry over: The phenomenon of carrying of water along with impurities by steam is called “carry over”. This is mainly due to priming and foaming. Priming and foaming mainly occur together.

2. Boiler corrosion: The “decay” or “disintegration” of boiler material either by a chemical or electrochemical reaction with its environment is known as “Boiler corrosion“.

3. Sludge and scale formation: Boilers are used for steam formation. When hard water is continuously evaporated in boilers, the continuous evaporation of water increases the concentration of dissolved salts until the water becomes saturated. Then the salts of Ca++ and Mg++ along with other soluble impurities are precipitated on the inner walls of boilers. When the precipitate formed is soft, slimy and loose, known as sludge and is hard and firmly adhering on the inner walls of boilers, known as scale.

4. Caustic embrittlement: This is the phenomenon during which the boiler material becomes brittle due to the accumulation of caustic substances. It is form of corrosion caused by high concentration of sodium hydroxide in boiler water. It is most likely to occur in boilers operating at high pressures, where NaOH is produced in the boiler by the hydrolysis of some residual Na2CO3 obtained from water softening process like lime soda.

 Na2CO3 + H2O = 2NaOH + CO2

The formation of NaOH makes the boiler water caustic. This caustic water penetrates into the minute hair cracks present in the inner side of boiler by capillary action. When the water evaporates and the concentration of dissolved NaOH increases progressively which attracts the surrounding area, thereby dissolving the iron of boiler as sodium ferrate.

Fe + 2NaOH = Na2FeO2 + H2O

Original source - Boilers

Tags: Boiler, Boilers, boiler, caustic, corrosion, issues, priming, water

Views: 104

Reply to This

Replies to This Discussion

The comments appear to be directed more at commercial steam systems, but there is no question that water quality is starting to become a major issue with hydronic systems as well. Here in Vermont, and New England, the use of boilers and hydronic heating is much more common than the rest of the nation, and the water quality of private water sources (drilled wells and springs) varies very widely. Many heating contractors are not paying attention to water quality and with the advent of IFCs (internal flow checks) and the more complex condensing boilers, homeowners are starting to pay the price.

I recently had two calls for no heat just days apart. One was a mid-efficiency low mass boiler, about 10 years old, and the other was a high efficiency condensing boiler, which last year replaced a similar mid-efficiency low mass boiler. Both systems are propane-fired and both have a mixture of radiant and baseboard heating. In both cases, the IFC in a circulator for a radiant zone had become so clogged with rust that there was no flow at all. In the first case, the pressure indicator on the tridicator was completely blocked and the mixing valves had corroded to the point of no longer operating.

It is imperative that heating contractors pay attention to the water quality of water going into their boilers, including makeup feed water, and that they periodically test the boiler water and condition it as needed.

RSS

Featured Forum Discussions

Stack/wind pressure and flow networks.

Started by Daniel James Grundy in Training. Last reply by William H Nickerson yesterday. 2 Replies

BDT with vermiculite in hollow CMU walls?

Started by Brad Cook in General Forum. Last reply by Sean Lintow Sr Mar 15. 1 Reply

Strange IR Image

Started by Larry Nissman in General Forum. Last reply by Brad Cook Mar 9. 7 Replies

Videos

  • Add Videos
  • View All

Latest Activity

Steve posted a discussion

Too many BTU's. Too much horsepower?

I have a 20 year old house with a 2 1/2 ton A/C for the lower floor and a 1 1/2 ton A/C for the…See More
10 hours ago
Profile IconSteve, Beth Edwards, Derrick Brodanex and 1 more joined Home Energy Pros
10 hours ago
Jill Lindman posted an event

High Performance Mechanicals for Houses That Work at Tacoma Power

May 25, 2017 from 8:30am to 4:30pm
High Performance Mechanical Systems for Houses That Work is a mid-level, full day seminar geared…See More
10 hours ago
Home Energy Magazine posted videos
13 hours ago
Diane Chojnowski posted events
yesterday
Richard Drohan liked eric anderson's discussion Energy auditing equipment for sale
yesterday
Richard Drohan replied to Jeffrey Anthony's discussion Blower Door Kits in the group Energy Auditing Equipment for Sale, Trade or to Purchase
"Please send pictures to rickdrohan@gmail.com.  thanks"
yesterday
Richard Drohan joined allen p tanner's group
Thumbnail

Energy Auditing Equipment for Sale, Trade or to Purchase

Discuss the pros and cons of the equipment you are interested in prior to purchase. Post equipment…See More
yesterday

Home Energy Pros

Welcome to Home Energy Pros – the unique digital community by and for those who work in the home energy performance arena.

Home Energy Pros was founded by the developers of Home Energy Saver Pro (supported by the U.S. Department of Energy) and brought to you in partnership with Home Energy magazine.  Home Energy Pros is sponsored by the Better Buildings Residential Network. Please honor our Guidelines

© 2017   Created by Lawrence Berkeley National Laboratory.   Powered by

Badges  |  Report an Issue  |  Terms of Service