weatherstripping-zen

The best-intentioned weatherstripping was too ambitious and one had to be too macho in order to close the patio doors. They wouldn't even lock.... Out it came.... Kermit is beaten, but not defeated....

Comment

You need to be a member of Home Energy Pros to add comments!

Join Home Energy Pros

Comment by Evan Mills on December 8, 2010 at 5:27pm
Debra - thanks for your generous info and insights on the flooring. Yes, humidity is >80% a lot of the time..... Moisture measurements on the floor surface facing the crawlspace (2x6 original T&G redwood which is under the bamboo, along with felt and 1/4" ply to level things off) were a few %-points above those in the flooring from the living space. We installed a continuous vapor barrier on the ground (yes, we may do a conditioned crawlspace ... not sure yet). Still have the cupping.
Comment by Debra Monte on December 8, 2010 at 3:00pm
Evan, I read the article and didn't see anything with regard to the flooring except that you do live in a humid area. Bamboo is very forgiving and stable, which allows it to be in high humidity. However, when the humidity levels are very high and or there are moisture problems or leaks, the cupping will appear. The good thing is that once the moisture or humidity problems are remediated, the bamboo will eventually lay totally flat and even again.

I experienced this myself. I moved into a fairly new home in 2008, where the previous owner only resided there for 7 years (first owner) and there was wall to wall carpeting throughout the house with the exception of the kitchen that had a vinyl flooring adhered to 1/4 inch thick Luan board, which was stapled with a miillion staples to the subfloor. Beneath the carpeting was only OSB sub-floor.

Of course, I wanted to also be green and installed 4 inch strand bamboo planks throughout the house, including the kitchen, over a thick multi-fiber insulayment. The baseboards were also strand bamboo, they cost a bit. My daughter's room was the only room where we installed a windsor oak plank.

About a year after the floor was installed, my daughter asked me to come and investigate a hissing sound coming from near the refigerator, which is in close proximity to the range. I didn't smell any gas and then decided to move the refrigerator out to inspect further and found that the cold water supply line to the rear of the refrigerator had sprouted a small leak that was continuously coming out behind the refigerator. The line was not made of copper, unfortunately it was just a cheap plastic line, sort of like a straw. Fortunately, there was a separate shut off valve under the sink and I did close it. No more cubes for now....

Of course, after wiping up what I could see, the floor eventually started to cup in the area in front of and around the refrigerator. This did not make me happy. However, after it was fully dried, perhaps a couple of weeks, the floor was back to normal with no cupping and no lasting damage.

Recently, we had the wonderful builder's grade toilet on the second floor overflow and somehow continuously shoot water out. Once I stopped it and wiped everything up, water had gone out of the bathroom into the hallway and soaked through to parts of the ceiling below. Within a few days the floor began to cup. This happened last week and I am hopeful that with a few weeks or so, it will go back to its normal condition.

So, find the source of all the moisture, repair/remediate and give the bamboo a little time to back into shape.
Good luck.
Comment by Mark Richardson on December 8, 2010 at 9:16am
Isn't that the Cantonese hyroglyph for "Distress?"
Comment by Evan Mills on December 7, 2010 at 8:22pm
Actually, the flooring is cupping (manufacturer blaming contractor and visa versa).... Kermit was right!
Comment by Debra Monte on December 7, 2010 at 8:11pm
Nice strand bamboo flooring though....

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy, under the American Recovery and Reinvestment Act) and brought to you in partnership with Home Energy magazine.

Latest Activity

Profile IconBoonPing Lim, Martin Easley and Richard Vito joined Home Energy Pros
27 minutes ago
Tom Delconte posted a discussion
2 hours ago
Tom Delconte replied to Johnny Ritzo's discussion Selecting a Water Heater
"J: natural gas is the cheapest, at least until prices skyrocket. Nearly everyone has gotten rid of…"
2 hours ago
Jeena Smith commented on Molly Banton's blog post Install a Pellet-Burning Fireplace Insert and Save Money
"Fireplace burning insert must be of very good quality. It should be a combo of lower price and high…"
8 hours ago
Johnny Ritzo posted a discussion

Selecting a Water Heater

I am looking at updating the heating and water heating systems in a rental home I recently…See More
12 hours ago
Eric Kjelshus replied to Patrick Michaelyan's discussion Hot Upper Stories
"When I am asked to fix this home.   I start with a Heat Loss and gain, blower door IR  sq…"
13 hours ago

Edward Foskey just added their location.
(via Member Map)

18 hours ago
Bud Poll replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans
"This is a topic I have discussed many times, but unfortunately cost is all too often the deciding…"
yesterday
Sean Lintow Sr replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans
"If you can't talk them into replacing with IC rated... Look into Tenmat - those are designed…"
yesterday
Bachi Brunato posted a discussion

Boxing and Insulating Around Non-ICAT Cans

I have a client with 16) 4" halogen recessed light fixtures in the attic.I'd like to cover the cans…See More
yesterday
Dennis Heidner replied to Patrick Michaelyan's discussion Hot Upper Stories
"Could you have them make a simple two line graph of the outside temperature, noting sun/clouds,…"
yesterday
Bob Blanchette replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??
"You make some valid points, especially with the base rate charges. Increasing the base rate instead…"
Saturday

© 2013   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service