"You note overheating on the south side (naturally.) Assuming the typical roof overhang of…"
Using thermal imagers in the summer
Too many thermographers leave their imagers in the case during the summer. This comes, in part, from the way we used to work when imagers were not nearly as sensitive and our understanding of how to use them was limited to winter work.
Get the darned thing out and use it! In most places, on most mornings, you can get successful "winter" images; if not, keep the home closed up for the night and add a bit of heat in the morning before you arrive.
Once the day warms, heat flow and thermal patterns will reverse. On days when the sun is intense, direct solar loading will make exterior work impossible during the daytime and even interior work will require patience and understanding of how the sun affects things. But it is not impossible by any means!
A few hours after sunset if the evening is warm and the AC on, imaging can be spectacular from both inside and outside.
With a blower door and the building depressurized, air leakage will nearly always be detectable. The image below of a house in the Bay area on a warm early afternoon shows poorly placed figberglass batts in a cathedral ceiling.
Want to learn more? My colleague, Matt Schwoegler, will be presenting a (paid) webinar on July 6 on Warm Weather Thermography. See http://www.thesnellgroup.com/Content/thermal-solutions-conference.aspx for details. You can also see his recent excellent article in the May/June issue of Home Energy Magazine.
I'd encourage all readers to take their imagers to every single job. If you don't get good images, think about why you didn't and, when possible, modify your protocols so the next time you have a better chance.
John
The Snell Group
Views: 312
Replies to This Discussion
-
Permalink Reply by Michael Stuart on -
I've got a few inspections in two weeks time. With my Ti32 and a blower door, I am good to go. (Sometimes I really don't even need the blower door. It's all about having the right training, and the right tools at your disposal.
-
-
Permalink Reply by Davide Lanzoni on -
If my memory is good, RESNET talk of a deltaT of only 3°F for conducting an infrared inspection with blower door: it happens many times and its' about a 100 mK NETD. here are some image with my Ti32. infiltration may be warm or hot, but you can see it almost always
-
-
Permalink Reply by John Snell on -
The 3F delta is for locating air leakage under RESNET. For locating insulation issues, an 18F delta is required. I agree we can often get by with less of a difference if we understand the conditions, know what we are doing and have a more sensitive imager—I favor something around 50mK, which is much more than 2X the sensitivity of a 100mK system. As always, Davide, very nice images!
-
-
Permalink Reply by John Snell on
-
Typically there are several reasons "hot work" is not as easy as working with cooler temperatures, and Matt will discuss these in his webinar next week. First, the delta-temperature (inside to outside) is usually not as great. Second, the sun loads the walls. While this may help, often is just confuses things. Finally, as materials cool quickly after a sunny day, differences in thermal capacitance reveal themselves; again, this may help but is often confusing. The attached image shows an exterior in the summer on a clear evening with AC running. The cement board siding has cooled quickly. The 3.5" FG batt insulation is in place. Is it working or only working poorly is it an issue of seeing cooling siding/still warm framing
or a combination of the factors? I find getting good results from summer thermography typically requires experience and skill, patience and a sensitive imaging system. -
-
Permalink Reply by Tyson Pischel on -
I have been setting up to inspect about 200 attics that are most likely completely out of compliance with ours(and any) reputable program specs. While testing a couple of remote camera configurations, I made a pass through the attic with my IR camera. As my attic was done correctly, The baffles (as shown on the left) were easy to spot. -
Home Energy Pros
Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy, under the American Recovery and Reinvestment Act) and brought to you in partnership with Home Energy magazine.
Latest Activity
Patrick Michaelyan replied to Patrick Michaelyan's discussion Hot Upper Stories"Thanks a lot Ed. And thanks to all who have added their two cents.
I think I know where to take…"
Ed Minch replied to Patrick Michaelyan's discussion Hot Upper Stories"We have successfully treated this same problem in perhaps 1000 of this same house in the…"
Craig Savage commented on Craig Savage's video
What is a Heat Pump Water Heater
"Hello Tom
We are working with A.O. Smith, GE and Stiebel Eltron on a Building America task to…"
Tom Delconte commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Craig: I was serious, since my propane price jumped from .98 to 1.85! according to everyone the GE…"
Ben Jacobs replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"I think that government support for good ideas results in major benefits over the long haul.
Please…"
Craig Savage commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Hello Tom
Not sure if you are being sarcastic, but a serious answer would be that GE is selling…"
Tom Delconte commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Craig: do you have a diagram of one that will run longer than one year? They don't really seem…"
Cory Chovanec replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"All good points brought up. My advice is not to leave the lights. When you said halogen I think…"
Jon Haehnel replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"The first 2 answers by Tom and Sean jive with my thinking and experience. Thank you Don for…"
Tom Smith replied to Patrick Michaelyan's discussion Hot Upper Stories"The most bang for your buck will come from airsealing the attic plane and sealing the…"
John Rising replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"Hi Bachi,
We have done many projects where we have installed boxes around recessed lights to…"
© 2013 Created by Lawrence Berkeley National Laboratory.
