Views: 594

Replies to This Discussion

Oh, that gave me a serious belly laugh at work. Jeez.

Sorry for the lack of focus -- new camera -- It's sitting on pavers on the right side but not the left.  It doesn't look too out of plumb in this shot but it was maybe 1" from top to floor.  The installer gets one brownie point for putting on a pipe-down but....this is soo bad.

Notice the duct tape around to protect the WH's finish from the strap which --- would have been better used around the dryer vent hose at least to seal it.

It should probably have had two straps for seismic hold down... and gas line looks like an opportunity for a small child to stand on and bounce.   That is also questionable... some states require a flexible connection between the appliance and the gas line - for seismic reasons.   It looks like the total length of the unsupported gas pipe might exceed four feet easily... and that should have been a code violation.   (can we say KABOOM...)

I really can't tell from the first picture how the venting is hooked up... was the plastic bag part of their vent system?  If so they may have suspected they had some kind of back draft problem... and tried to cure that with the bag?  I can't imagine a mechanical permit was pulled to install the heater... a licensed person would not have done that...  it had to be a DIY job.

This is also a powered vent hot water heater... nice electrical installation....   :-(   at least there would be a source of ignition for the broken gas line...  

One last comment -- click on pictures... the first picture changes when you click on it so you can actually see the blocking under one side.

Most gas hot water heaters are also supposed to be place about a foot above the floor -- such that fumes from a flammable source remain below the level of the pilot... this installation also lacks that....

As far as seismic activity -- this is PA not CA so no WH's have hold downs here...I don't like the gas line either but I think the reason why the WH is leaning is b/c they wanted to hook up to the existing line.

 I agree with seeing an opportunity for children's play.  I'll check the code on that.

 The plastic bag had the operating manual in it -- it's not part of the installation ( incidentally, the installation manual was no where to be found) -- had to look it up on line.  The new foil slinky hose connects to the existing 3" PVC running between the floor joists and out to the sidewall about 10' away.

 Yeah -- you should have to have a master plumber change out a WH in this municipality but it kinda looks like someone was flying under the radar on this one.  I think the WH power cord is plugged into the furnace outlet -- I forget just what was going on there...

Thx for the comment about the pictures -- I loaded 2 the first time and then couldn't find the second one so I loaded another one -- I'm still getting the hang of this software, I guess.

There's not room to put it up any higher than it is really.  But I'll mention no flammables storage to the homeowners.

I'm pretty sure code would also require separate outlet for the WH... it should not be piggy backed off the breaker for the furnace...even though it is a low current device.   Similar rules (some states) are for separate outlets for washer & dryers (even gas dryers).

I'd still check current codes about seismic ties for WH...the northeast and midwest has had earthquakes... and other disasters... so I suspect even the PA state buiding codes may require some kind of simple tie to the structure.

Since there is power going to the vent fan for the furnace... you should also check to see if there is a requirement for bonding the water pipes to the earth ground at the electric panel...

It's all better now.  It's sitting plumb with glued PVC venting and the gas line is shorter, closer to the wall, and strapped to the floor joist above.  And I checked the gas line from the basement wall where the meter is all the way to the furnace and WH -- no leaks.

Cool... a success story... without the fireworks...

Amen! -- you can say that again.

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Richard Beyer replied to Howard Katzman's discussion UV lights on filters
"Howard, There are numerous manufacturer's who swear these systems work and then you have the…"
2 hours ago
Christopher Morin posted a blog post

How do You Test a TXV?

  Thermostatic Expansion Valves (TEV or TXV), one of the most popular metering devices for…See More
6 hours ago
Howard Katzman posted a discussion

UV lights on filters

 recently saw UV bulb installations in 2 HVAC systems in a home. Each system had the Lennox Healthy…See More
8 hours ago
Don Fitchett joined Michael Stuart's group
Thumbnail

INFRARED THERMOGRAPHY USERS

This group is dedicated to knowledge sharing and discussion of infrared thermography for building…See More
8 hours ago
Don Fitchett commented on Diane Chojnowski's group Pinterest
"While most of our (BIN95.com) energy post and boards are industrial related, there are crossovers…"
8 hours ago
Don Fitchett joined Diane Chojnowski's group
Thumbnail

Pinterest

Do you have a Pinterest board for energy topics?Post the link to your Pinterest energy board in the…See More
9 hours ago
Profile IconJosh Guenther, Deborah Green, Kenneth Brooks and 3 more joined Home Energy Pros
9 hours ago
Jim Gunshinan commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"Hi David, to answer one question, the crawlspace was covered with thick poly and the seams were…"
10 hours ago
David Eakin commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"Jim, Maybe a little more detail on the project is in order. You say that your crawlspace is now…"
10 hours ago
Jim Gunshinan commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"Ed, no problem, I caught your meaning. Ted, I made a judgement that a mini split would be the best…"
10 hours ago
tedkidd commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"That makes sense.   What are your criteria/metrics for determining what might be the…"
10 hours ago
Ed Voytovich commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"Yikes!  Not only did I misspell "roof" as "rood," I also meant to more…"
10 hours ago

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service