I have been going with a relatively unique (and time-consuming) approach to address two similar situations: vented cathedral ceilings and semi-conditioned attics with HVAC equipment.

I have been combining 3/4" Dow Tuff-R polyiso and R-21 high-density FGB insulation to achieve both an air barrier, a partial radiant barrier, and roughly an R-30 in 2X8 roof rafter assemblies (in older homes in Northern VA).

The 3/4" Dow Tuff-R is set 1" from the sheathing (with a ridge vent retro'd in to the roof, and natural ventilation at the roof-fascia intersection). The edges of the Tuff-R are sealed with closed-cell foam, and the joints taped with Nashua Extreme Weather foil tape. The remainder of the cavity is then filled with R-21 HD batts. Ducts in semi-conditioned attics are often sealed.

With recessed lights in cathedral ceilings, I try to get as much polyiso above the can housing (and swap out bulbs to LEDs), while maintaining an air space beneath the sheathing.

I have come to really appreciate the approach, but I wanted to bounce this off the pros before I continue my love affair with this approach.

Thanks in advance!

Views: 242

Replies to This Discussion

Sounds good at first blush & used similar approach for others (minus leaving can lights) - As an FYI it is R26 technically & I am assuming by radiant barrier this one has the foil facing & it is facing the sheathing?

For the tape, make sure you check with DOW to make sure they approve but that sounds good

How are you getting the 1" gap?

Now the problem I see - even with LEDS, those cans are not rated for foam to be touching them, only items like FG, rock wool, & cellulose should be touching (assuming IC Rating)

Thanks for the reply Sean.

I have been using 1" polyiso sleepers to achieve the 1" air space between the roof sheathing and the polyiso board.

I have indeed been using the foil-faced product.

I will look into the tape and whether Dow approves. Any advice on finding that info out without scouring Dow's entire site?

I will have to look further into the can lights and the issue you raise with foam coming into contact with them.

Look at there spec / installation directions or call there technical support department or regional rep if not listed - generally pretty good at answering questions

RSS

Discussion Forum

Moisture/Mold on rim joist;

Started by John Shillito. Last reply by John Nicholas Jan 10. 6 Replies

Radon - Passive Systems

Started by Sean Lintow Sr. Last reply by Bryan Gabriel Jan 5. 5 Replies

Vented Soffit! DO or DON'T?

Started by Daniel Baur-McGuire. Last reply by Daniel Baur-McGuire Nov 15, 2016. 13 Replies

Water Saver or Gimmick?

Started by Sean Lintow Sr. Last reply by Bob Blanchette Oct 23, 2016. 18 Replies

Duct Testing - is a change in order?

Started by Sean Lintow Sr. Last reply by Sean Lintow Sr Aug 6, 2015. 20 Replies

Latest Activity

Laurie DiDonato updated an event

Hybrid HERS Rater Training September 2017 (NH) at Online/ Classroom in Manchester, NH

September 11, 2017 at 9am to October 6, 2017 at 5pm
EARLY BIRD DISCOUNT: Register by August 15th and get $200 off!This training has been approved by…See More
11 hours ago
Profile IconEmily Rhea, Spray-on Foam and Keith Flores joined Home Energy Pros
Friday
Kent Browning replied to Brandon Walton's discussion When is it too windy to use blower door?
"I found this post thru a Google search. I was already a member and have posted a few times. I am a…"
Friday
Home Energy Magazine's video was featured

2017 U.S. Department of Energy Race to Zero Student Design Competition

The U.S. Department of Energy (DOE) Race to Zero Student Design Competition (Race to Zero) inspires collegiate students to become the next generation of buil...
Friday

Photos

Loading…
  • Add Photos
  • View All

© 2017   Created by Lawrence Berkeley National Laboratory.   Powered by

Badges  |  Report an Issue  |  Terms of Service