I have been going with a relatively unique (and time-consuming) approach to address two similar situations: vented cathedral ceilings and semi-conditioned attics with HVAC equipment.

I have been combining 3/4" Dow Tuff-R polyiso and R-21 high-density FGB insulation to achieve both an air barrier, a partial radiant barrier, and roughly an R-30 in 2X8 roof rafter assemblies (in older homes in Northern VA).

The 3/4" Dow Tuff-R is set 1" from the sheathing (with a ridge vent retro'd in to the roof, and natural ventilation at the roof-fascia intersection). The edges of the Tuff-R are sealed with closed-cell foam, and the joints taped with Nashua Extreme Weather foil tape. The remainder of the cavity is then filled with R-21 HD batts. Ducts in semi-conditioned attics are often sealed.

With recessed lights in cathedral ceilings, I try to get as much polyiso above the can housing (and swap out bulbs to LEDs), while maintaining an air space beneath the sheathing.

I have come to really appreciate the approach, but I wanted to bounce this off the pros before I continue my love affair with this approach.

Thanks in advance!

Views: 70

Replies to This Discussion

Sounds good at first blush & used similar approach for others (minus leaving can lights) - As an FYI it is R26 technically & I am assuming by radiant barrier this one has the foil facing & it is facing the sheathing?

For the tape, make sure you check with DOW to make sure they approve but that sounds good

How are you getting the 1" gap?

Now the problem I see - even with LEDS, those cans are not rated for foam to be touching them, only items like FG, rock wool, & cellulose should be touching (assuming IC Rating)

Thanks for the reply Sean.

I have been using 1" polyiso sleepers to achieve the 1" air space between the roof sheathing and the polyiso board.

I have indeed been using the foil-faced product.

I will look into the tape and whether Dow approves. Any advice on finding that info out without scouring Dow's entire site?

I will have to look further into the can lights and the issue you raise with foam coming into contact with them.

Look at there spec / installation directions or call there technical support department or regional rep if not listed - generally pretty good at answering questions

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Jim Gunshinan commented on Jim Gunshinan's blog post Energy Upgrade California—Up Close and Personal
"I had a revelation while attending Bruce Manclark's session of duct leak testing at the Energy…"
7 hours ago
George J. Nesbitt commented on Jim Gunshinan's blog post Energy Upgrade California—Up Close and Personal
"Blower Door; the 2007 test was a depressurization test, and the 2014 a pressurization test, which…"
7 hours ago
George J. Nesbitt replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Plan, plan, plan, plan. The 1st step to is to understand the house, how it's built, the…"
7 hours ago
George J. Nesbitt posted an event

High Performance Windows - A Panel of Experts at Pyramid Alehouse`

April 26, 2014 from 3pm to 5pm
Join a lively panel discussion on high performance windows. We'll cover some basics, as well as…See More
9 hours ago
Kaushal Bharath Raju replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Hi David, Thanks for pointing out Martin Holiday's article. I do not wish to engage in the…"
9 hours ago
Profile IconAdam Penberthy, Scot Davidson and j jarvella joined Home Energy Pros
9 hours ago
David Eakin replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"More food for thought on this subject - read this (fairly) recent blog by one of the most respected…"
14 hours ago
Curt Kinder commented on Christopher Morin's blog post 5 Things New Energy Efficiency HVAC Contractors Need to Know
"You left out air distribution...Without at least a passing glance at how much air moves through the…"
20 hours ago
David Eakin replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"I mis-spoke - I was referring to the Midori House in Santa Cruz. Have an in-depth discussion with…"
yesterday
Kaushal Bharath Raju replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Hi David & Bud, $400/sqf > $300 sqf. The latter is the minimum cost of new construction in…"
yesterday
David Eakin replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Kaushal, There was a deep energy retrofit upgrade project (to Passive House standards) in San Jose…"
yesterday
Kim Tanner updated an event

Beyond Residential Testing at The Energy Conservatory

May 14, 2014 to May 16, 2014
The Energy Conservatory (TEC) is hosting a Beyond Residential Testing event. In addition we are…See More
yesterday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service