In an earlier post, I talked about 3 of the most important strategies for making a home energy efficient. They were; 1. Air sealing, 2. Air sealing, and 3. Air sealing.

Air sealed, or tight, homes do a better job at containing the conditioned air coming from the HVAC system where it belongs…inside. Tight homes also keep the unwanted hot/humid or cold/dry outdoor air where it belongs…outside. Both of these keep your HVAC system running less, which ultimately reduces your energy bill. In other words, the home is more efficient.

Fresh air should be brought in to the home through mechanical ventilation, which maintains proper levels that fresh air, and can also filter and condition it depending on the type of ventilation strategy employed in your home.

By the way: Tight homes also do a better job at keeping moisture, pollutants, sound and insects from getting!

Stopping Air Flow

If you’ve read Part I and Part II of this series, you’ll remember this detail (below). In the earlier posts, we point out our strategies for controlling moisture and heat flow at the slab-on-grade condition of the Proud Green Home at Serenbe. Today, it’s all about air sealing. (Note: this detail is for a home in North GA, or Climate Zone 3A. Local conditions vary, and each home should be designed for it’s local climate)

Designing for High Performance Slab-On-Grad Part III Controlling Air Flow

The 1″ Zip System R-Panel is made up of the widely used Zip System wall sheathing and a 1/2″ layer of EPS foam insulation. Each of these materials are well know air barriers on their own, but have been brought together in to a single product to act as a structural component, air barrier and thermal break. As is done with their sheathing, Zip Systems Tape is applied to all seams between each panel and at all penetrations. Windows are given extra attention to properly flash so as to prevent air and/or water from finding it’s way back in to the building.

The Zip System Tape not only performs very well at all sheathing seams and penetrations, but it also adheres very well to concrete. In fact, it is one of the better products for this application. We are applying a continuous strip of the tape at the bottom of the R-Panel where it meets the foundation wall. This will prevent air flow at the base of the panels.

The sill gasket shown below the bottom plate, in conjunction with the continuous Zip Tape at the exterior seam between the plate and slab, works well at an area know for a lot of infiltration. We’re also going to be applying a continuous strip of the tape on the inside of the wall at plate-slab junction to provide insurance for a tight seal. Similar attention will be paid to the top of the wall where we will have double plates. Another prime location for air leakage.

Above the slab

In the walls, you will see we will be completely filling the cavities with expanding open-cell spray foam. When installed properly, spray foam will not only insulate our walls but will provide an excellent air barrier in and around the entire cavity.

Finally, we’ve chosen Marvin’s Integrity Windows because of their durability and low air leakage rate. We will install sealant on the back side of the window fin before placing it in the opening. Then, we will use expanding foam between the window and the sill, jambs and head.

Tags: air, controlling, design, efficiency, energy, flow, high, performance, sealing

Views: 2821

Replies to This Discussion

I like that detail of the Home Slicker over the Zip system which eliminates one of my concerns of water being able to collect on the tape ridge plus you add the drainage plane - nice piece & explanation

Any testing for sheerwalls out on these panels yet?

Thanks, Sean.

Here is the ICC-ES report for the R-Panel. They are still working on testing it to use as roof sheathing...still working...

http://www.zipsystem.com/uploads/technical-tips/ESR-3373%20(6-1-12)...

What is the average cost per square foot of the ZIP panel and can I find this product in the intermountain region.

Does the insulated Zip R-panel allow water vapor to pass to the outside, for cold climate installation?

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Hal Skinner replied to Richard Beyer's discussion Spontaneous Combustion and Flash Fire regarding Spray Foam Insulation
"Richard, here is something else that might be pertinent. In my hundreds of conversations with our…"
16 hours ago
Trip posted a discussion

Starting a Home Weatherization Business. Considering it...

I am considering starting a home weatherization business. (I live in Southeast Alabama)  Currently…See More
17 hours ago
Jim Gunshinan commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"To all, one thing I don't lack is advice from the experts! Thanks for the input, challenges,…"
18 hours ago
tedkidd commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"Jim, I'm glad you are open, that's great!  We all learn best when we are open! The…"
18 hours ago
David Eakin commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"Jim, Well, as the editor of Home Energy you should already know that the order of remediation is…"
18 hours ago
Greg Labbe posted a blog post

Technical Tape Desecration

Lets face it – building science is pushing the performance of adhesive tapes to a new levels and…See More
20 hours ago
Stacy Hunt posted an event

High Performance Enclosure Strategies: Part II, New Construction at Online

August 13, 2014 from 1pm to 2:30pm
Please join the Building America Program for our free webinar: High Performance Enclosure…See More
22 hours ago
Richard Beyer replied to Howard Katzman's discussion UV lights on filters
"Howard, There are numerous manufacturer's who swear these systems work and then you have the…"
yesterday
Christopher Morin posted a blog post

How do You Test a TXV?

  Thermostatic Expansion Valves (TEV or TXV), one of the most popular metering devices for…See More
yesterday
Howard Katzman posted a discussion

UV lights on filters

I recently saw UV bulb installations in 2 HVAC systems in a home. Each system had the Lennox…See More
yesterday
Don Fitchett joined Michael Stuart's group
Thumbnail

INFRARED THERMOGRAPHY USERS

This group is dedicated to knowledge sharing and discussion of infrared thermography for building…See More
yesterday
Don Fitchett commented on Diane Chojnowski's group Pinterest
"While most of our (BIN95.com) energy post and boards are industrial related, there are crossovers…"
yesterday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service