Before we had our high tech tools, how did we know if there was insulation in the walls? What were the methods?

How funny that I can use a camera but than can't figure out how was it done in the past without drilling holes on the wall and than you had to patch it? That doesn't seem like a cost effective way to bid a job. Or is it another rule of thumb? Like In So. Cal houses built before the 70's we can assume that there is no wall insulation. I am sure on the East Coast that insulation is a MUST. 

Views: 46

Replies to This Discussion

Well I just simply pop the cover off a few light switches & electrical outlets & shined a light in there. If I didn't see anything I would take a bent coat hanger & use it to fish around in there some.

 

Generally if we are remodeling a house / gutting  a room to the studs I will add in new insulation anyways due to new electrical, plumbing, etc... & the old insulation is probably shot. The only surprise I had was the 1879 remodel we did where it was fully packed with a wool type insulation that stayed in place & was still in great shape.

A crocheting hook used at an electrical outlet on an exterior wall can reveal the presence or lack of insulation.

Common practice in the Minneapolis area for the past 20 years has been to drill a 2” hole in a closet on an outside wall and snap a plastic plug into the hole after verifying the insulation level.  This would be done for any home built before about 1970.  It is possible for a wall to look insulated using the IR and have only 1.5 inches of insulation in the wall.  In our climate it is cost effective to dense pack cellulose into a wall that has an existing 1.5” insulation batt.  Sometimes on homes build before 1920, the walls will have no insulation but have back-plaster.  Back-plaster is an additional layer of plaster that was installed in the center of the wall cavity, making it more much expensive to insulate.  The IR is a great tool but it has limitations.

In reply to probing around ext. wall outlets, the problem is that batt insulation is usually installed poorly. By only probing in these locations you run the risk of determining that no existing insul. is in the wall because it was cut out too big around the box. The other error is compacted insul. around the box because it was not cut at all.

I would agree that the best practice is to drill inspection holes in the closet of an exterior wall and plug them. Of course this is dependent on H/O approval.

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Kurt Shafer replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Reading the Invisco description you will find that it is designed to be surrounded by cellulose to…"
8 hours ago
Glen Gallo replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Kurt, I think cost of operation is always a factor but I am not sure I would leave it just cfm.…"
9 hours ago

Paul DelVaglio just added their location.
(via Member Map)

10 hours ago
Paul DelVaglio posted a photo
11 hours ago
reflintorm replied to Jamie Kaye's discussion Flickering LED lights
"I think, Better to replace the dimmer switch if it is not recovered then once go through the…"
15 hours ago
Kurt Shafer replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Glen,  You are the first person who has ever told me they prefer lower CFM. What you left out…"
yesterday
Glen Gallo replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Tamarack has lower CFM than typical fans and has a insulated lid that automatically closes when fan…"
yesterday
Tom Conlon's discussion was featured

Whole House Fans - Love 'Em or Not?

I just searched this forum for "Whole House Fan", but I didn't find much about them (except …See More
yesterday
Tom White shared Brandon Walton's blog post on Twitter
yesterday
Brandon Walton's blog post was featured

12 Things Every Home Performance Contractor Should Have on Their Work Truck

Every home is unique and differs from the last. It would be a perfect world (from a project…See More
yesterday
Griffin Hagle replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
yesterday
Griffin Hagle replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Kurt, Whoops, looks like I got my links mixed up. Thanks for pointing that out. Here's the…"
yesterday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service