BPI's April Stump the Chump: What’s Wrong with this Picture?

Replies to This Discussion

Permalink Reply by Craig Bird on April 17, 2012 at 3:26pm

Problem is Ice Dams.  The home most likely had melting of roof snow which then refroze and created ice dams possibly causing water damage or excessive ice buildup at roof edges. This caused the homeowner to install energy intensive heat strips to melt the ice dams and jack their electric bill through the roof during snow events.  

 

This is caused by:

1)      Air leakage from penetrations near exterior wall

2)      Heat sources close to exterior wall such as heating ducts or recessed lighting cans

3)      Insulation in contact with roof sheathing causing thermal bridging to roof deck

4)      Lack of soffit ventilation

 

The solution:

 

1)      Air seal exterior top plate with spray foam. It is also important to air seal any other penetration which is delivering heat to the underside of the roof deck.

2)      If recessed lighting is installed near exterior walls, the cans should be ICAT rated to prevent air flow through the fixture. An inexpensive air tight trim kit may also be purchased to avoid changing out fixture itself. Heating duct boots can be sprayed with 2 part foam to prevent heating of roof deck.

3)      Install soffit ventilation at code recommended level at EVERY BAY that is affected.

4)      Install insulation baffles at all soffit edges in order to provide a path for ventilation and carry away any remaing heat transferred from house and cool roof deck. This also prevents insulation from contacting the roof deck (causing thermal bridging).

 

Since it is often difficult to get full insulation amounts at the soffit edge due to clearance, an optimal solution would involve installing ventilation baffles and using spray foam insulation against the baffle and as far in until a full amount of blown insulation may be used. This solution also seals any air exfiltration through the wall top plate at the same time. 

 

 

• ▶ Reply

Permalink Reply by Craig Bird on April 19, 2012 at 10:34am

Oh, and most likely, this is the north facing roof your looking at, unless you have tons of winter shade on the southern exposure.

• ▶ Reply

Permalink Reply by Cierra Mooney on May 15, 2012 at 8:03am

Congratulations to Craig Bird of Preston Insulation in Tucson, Arizona for winning last month’s “What’s wrong with this picture?”contest. Craig was not only the first person to send in the correct answer. His answer was far and away the most comprehensive, and dare we say, the most elegant in illustrating what in the world of home performance was wrong with the picture, and what should be done about it.

The picture shows a snow-bound house in front of Lake Tahoe, its roof zig zagged with heat strips.  Says Craig:

“The problem is ice dams.  The home most likely had melting of roof snow which then refroze and created ice dams possibly causing water damage or excessive ice buildup at roof edges. This caused the homeowner to install energy intensive heat strips to melt the ice dams and jack their electric bill through the roof during snow events.  

 

This is caused by:

1)     Air leakage from penetrations near exterior wall

2)     Heat sources close to exterior wall such as heating ducts or recessed lighting cans

3)     Insulation in contact with roof sheathing causing thermal bridging to roof deck

4)     Lack of soffit ventilation

 

The solution:

1)     Air seal exterior top plate with spray foam. It is also important to air seal any other penetration which is delivering heat to the underside of the roof deck.

2)     If recessed lighting is installed near exterior walls, the cans should be ICAT rated to prevent air flow through the fixture. An inexpensive air tight trim kit may also be purchased to avoid changing out fixture itself. Heating duct boots can be sprayed with 2 part foam to prevent heating of roof deck.

3)     Install soffit ventilation at code recommended level at EVERY BAY that is affected.

4)     Install insulation baffles at all soffit edges in order to provide a path for ventilation and carry away any remaining heat transferred from house and cool roof deck. This also prevents insulation from contacting the roof deck (causing thermal bridging).

 

Since it is often difficult to get full insulation amounts at the soffit edge due to clearance, an optimal solution would involve installing ventilation baffles and using spray foam insulation against the baffle and as far in until a full amount of blown insulation may be used. This solution also seals any air exfiltration through the wall top plate at the same time. 

• ▶ Reply