BPI's April Stump the Chump: What’s Wrong with this Picture?

We know, we know. There’s a lot right with this picture, such as the gorgeous view of Lake Tahoe in the background and the awesome powder for skiing. But from a whole-house-as-a-system perspective, what’s wrong with this picture? What is the owner trying to do, and what would be a better solution?

Thanks to our own Larry Zarker, BPI CEO, for sending in this dandy shot. He offers the following Winston Churchill quote to explain what’s going on here: “You can always trust the Americans to get it right, after they have exhausted every other possibility”.

Think you know what the problem is, as well as the solution? Send it to us at lmcdowell@bpi.org.

 

Tags: April, Chump, Stump, building, newsletter, performance, the

Views: 360

Reply to This

Replies to This Discussion

Problem is Ice Dams.  The home most likely had melting of roof snow which then refroze and created ice dams possibly causing water damage or excessive ice buildup at roof edges. This caused the homeowner to install energy intensive heat strips to melt the ice dams and jack their electric bill through the roof during snow events.  

 

This is caused by:

1)      Air leakage from penetrations near exterior wall

2)      Heat sources close to exterior wall such as heating ducts or recessed lighting cans

3)      Insulation in contact with roof sheathing causing thermal bridging to roof deck

4)      Lack of soffit ventilation

 

The solution:

 

1)      Air seal exterior top plate with spray foam. It is also important to air seal any other penetration which is delivering heat to the underside of the roof deck.

2)      If recessed lighting is installed near exterior walls, the cans should be ICAT rated to prevent air flow through the fixture. An inexpensive air tight trim kit may also be purchased to avoid changing out fixture itself. Heating duct boots can be sprayed with 2 part foam to prevent heating of roof deck.

3)      Install soffit ventilation at code recommended level at EVERY BAY that is affected.

4)      Install insulation baffles at all soffit edges in order to provide a path for ventilation and carry away any remaing heat transferred from house and cool roof deck. This also prevents insulation from contacting the roof deck (causing thermal bridging).

 

Since it is often difficult to get full insulation amounts at the soffit edge due to clearance, an optimal solution would involve installing ventilation baffles and using spray foam insulation against the baffle and as far in until a full amount of blown insulation may be used. This solution also seals any air exfiltration through the wall top plate at the same time. 

 

 

Oh, and most likely, this is the north facing roof your looking at, unless you have tons of winter shade on the southern exposure.

Congratulations to Craig Bird of Preston Insulation in Tucson, Arizona for winning last month’s “What’s wrong with this picture?”contest. Craig was not only the first person to send in the correct answer. His answer was far and away the most comprehensive, and dare we say, the most elegant in illustrating what in the world of home performance was wrong with the picture, and what should be done about it.

The picture shows a snow-bound house in front of Lake Tahoe, its roof zig zagged with heat strips.  Says Craig:

“The problem is ice dams.  The home most likely had melting of roof snow which then refroze and created ice dams possibly causing water damage or excessive ice buildup at roof edges. This caused the homeowner to install energy intensive heat strips to melt the ice dams and jack their electric bill through the roof during snow events.  

 

This is caused by:

1)     Air leakage from penetrations near exterior wall

2)     Heat sources close to exterior wall such as heating ducts or recessed lighting cans

3)     Insulation in contact with roof sheathing causing thermal bridging to roof deck

4)     Lack of soffit ventilation

 

The solution:

1)     Air seal exterior top plate with spray foam. It is also important to air seal any other penetration which is delivering heat to the underside of the roof deck.

2)     If recessed lighting is installed near exterior walls, the cans should be ICAT rated to prevent air flow through the fixture. An inexpensive air tight trim kit may also be purchased to avoid changing out fixture itself. Heating duct boots can be sprayed with 2 part foam to prevent heating of roof deck.

3)     Install soffit ventilation at code recommended level at EVERY BAY that is affected.

4)     Install insulation baffles at all soffit edges in order to provide a path for ventilation and carry away any remaining heat transferred from house and cool roof deck. This also prevents insulation from contacting the roof deck (causing thermal bridging).

 

Since it is often difficult to get full insulation amounts at the soffit edge due to clearance, an optimal solution would involve installing ventilation baffles and using spray foam insulation against the baffle and as far in until a full amount of blown insulation may be used. This solution also seals any air exfiltration through the wall top plate at the same time. 

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Richard Vito joined Sean Lintow Sr's group
Thumbnail

Best Practices (Residential)

Best Building, Retrofitting, or even Auditing Practices - what are they, what should change, what…See More
3 hours ago
Richard Vito joined James Sayers's group
Thumbnail

Marketing Energy Efficiency

Sharing ideas, tools and examples of promoting energy efficiency to consumersSee More
3 hours ago
Richard Vito joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
3 hours ago
Richard Vito joined Kyle Brown's group
Thumbnail

Wrightsoft - Manual J / Manual D

If you use Wrightsoft to calculate loads or design ducts, you likely have questions.  Get answers…See More
3 hours ago
Richard Vito joined allen p tanner's group
Thumbnail

Energy Auditing Equipment for Sale, Trade or to Purchase

Discuss the pros and cons of the equipment you are interested in prior to purchase. Post equipment…See More
3 hours ago
Jim Gunshinan commented on Jim Gunshinan's blog post Energy Upgrade California—Up Close and Personal
"I had a revelation while attending Bruce Manclark's session of duct leak testing at the Energy…"
17 hours ago
George J. Nesbitt commented on Jim Gunshinan's blog post Energy Upgrade California—Up Close and Personal
"Blower Door; the 2007 test was a depressurization test, and the 2014 a pressurization test, which…"
17 hours ago
George J. Nesbitt replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Plan, plan, plan, plan. The 1st step to is to understand the house, how it's built, the…"
18 hours ago
George J. Nesbitt posted an event

High Performance Windows - A Panel of Experts at Pyramid Alehouse`

April 26, 2014 from 3pm to 5pm
Join a lively panel discussion on high performance windows. We'll cover some basics, as well as…See More
19 hours ago
Kaushal Bharath Raju replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Hi David, Thanks for pointing out Martin Holiday's article. I do not wish to engage in the…"
19 hours ago
Profile IconAdam Penberthy, Scot Davidson and j jarvella joined Home Energy Pros
19 hours ago
David Eakin replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"More food for thought on this subject - read this (fairly) recent blog by one of the most respected…"
yesterday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service