A client had a new double wide set (27x56) in1997 a couple years later had an addition (27x20) to the west side with 27x20 attached garage to that addition, the general contractor tells the client a bigger furnace will be needed. He (general contractor) brings in his HVAC guy who installs a furnace clearly stamped "Installation for site built only", the front of the return box was hacked out to provide for a 16x20 filter plus the back has a run coming off of it into the master bed closet with a filter slot (no filter in place)down into the crawl and up into the wall cavities of the addition all metal return ducting uninsulated in crawl. The supply to addition comes off the original duct board below the furnace through the crawl to four insulated flex runs in addition and for some reason they insulated ,or tried to,  the metal ducting in addition crawl but not under manufacture home crawl and to make sure the owner got a good job the jumper duct was cut about four out from the furnace and left that way. The only thing I can come up with is they were going to tie into to the new heat run and forgot. So forget the general contractor, HVAC guy and last but not least the county inspector, so now what. As far as I'm concered that furnace has got to go and "Manufacture Home" approved installed, period. For the supply runs remove all that ducting, seal duct board back up and tie into bottom of original ducting at each west end run with insulated flex to existing boots, and naturally new jumper. I'm thinking the return in addition can go, the passage way to addition is over 8'. What are your thoughts, am I on the right track or in line with the three fore mentioned proffesionals. "The things that make your head go," BOOM ! " 

Views: 128

Reply to This

Replies to This Discussion

The manufacture home has higher SP ( rated Static Pressure) supply and no return  so some are rated to .8 to 1" in water vs most res are .5 in water.  Most Manufacture homes have a little room off the hall way  so the fan is a foot from door with wimpy filter.  Manufacture home have no branch duct just a 5" stream off the main trunk.     That's 2597 SF and Mob home air handler have higher efficiency  with smaller area,  With the transfer main trunk the efficiency just drops 10-15%

  Manufacture homes furnaces also take outside air on outside the flue pipe and have to buy the chimney from them.  When test system Efficiency (BTU in Vs BTU out) I get mid 40% on new and low 30% on old duct work.    To me it’s just temporally housing with high power bills.

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Luis Hernandez posted a discussion

Air Source Heat pump or mini-split efficiency

Greetings everyone!    I have a technical questions I hope I could get some feedback! I understood…See More
1 hour ago
Jim Gunshinan posted blog posts
18 hours ago
H.O. Electric posted a photo

about us-team

H.O. Services is your residential Electric-Plumbing-Heating-Cooling Specialist. We are an…
19 hours ago
H.O. Electric added a discussion to the group News & Announcements
Thumbnail

Stay Cool With Easy To Install Ductless AC System!

Stay Cool With Easy To Install Ductless AC System!   Save $300.00 Off A New AC System For A Limited…See More
19 hours ago
Richard Wells commented on Diane Chojnowski's group Facebook Pages
"Three thousand home energy efficiency audits, and nearly a thousand retrofits in four short…"
20 hours ago
Richard Wells joined Diane Chojnowski's group
Thumbnail

Facebook Pages

Does your company or organization have a Facebook Page?This group is for pros who have facebook…See More
20 hours ago
David Baerg replied to Blake Shurtz's discussion Air sealing wood-burning fireplace from the crawlspace below
"Hi Blake, Do you mean around the underside of the hearth?  Are you trying to seal between the…"
21 hours ago
Tom White's video was featured

Rebirth Realty: Restoring Detroit properties for Venture for America Fellows

Its been a long, cold winter, but we've made significant progress in the restoration of 760 Virginia Park. Join Tim Dingman on a walkthrough to see what we've done.
22 hours ago
Kim Tanner added a discussion to the group Multifamily Buildings
Thumbnail

Blower Door Applications Guide

TEC and Camroden Associates have released their big building testing manual, Blower Door…See More
22 hours ago
Profile Iconmichael coleman, Dan Liska and Rob Moreno joined Home Energy Pros
23 hours ago
Christopher Morin's blog post was featured

5 Things New Energy Efficiency HVAC Contractors Need to Know

1. Do not sell on Price! Use 'Simple Payback'The price of High-efficient equipment will undoubtedly…See More
yesterday
Jim Gunshinan's blog post was featured
yesterday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service