Tired of climbing ladders and reaching to find air leaks during blower door test I have a solution!!!

Yes, a thermal image camera is a good way, but a better way to instantly see the leak and the cfm amount of the leak-- try using the Alnor thermoanemometer Model 8565.    Cheap on ebay for $100.

 Plus the Alnor has a 4 foot reach.   No need for silly smokers.

Tags: air, blower, door, sealing, testing

Views: 869

Reply to This

Replies to This Discussion

Can you explain how you would use the thermoanemometer and your criteria for air flow to determine excessive leakage?  Besides, doesn't the anemometer measure just velocity (fpm) not volume of air (cfm) unless you know the ft2 area of the opening?  Unless its leakage through a regularly shaped opening, like a wall outlet hole, how do you estimate the area of a crack, for example, to determine cfm?

You haven't convinced us yet. To my knowledge there is not a replacement for IR, smoke, sight, and good old experience. I use the blower door and IR to find air leaks in record time without using a ladder, but if I want to know how much leakage I am seeing there is no gadget for that. Total path zone leakage testing or measuring the hole are your best bet. If you could elaborate on the gadget you speak of and explain how you get a cfm reading I would be open to changing my opinion.

Take for instance when you crack open a bedroom door during a blower door depressurization test, the Thermoanemometer will tell you exactly the fpm of airflow which is easily converted to cfm leakage. This information is not obtainable with an IR, smoker or back of your hand. I am having a great time using this tool. I hate smokers etc.

You really didn't answer how you use that cfm number.  Are you just comparing relative cfm values for each room, or do you have a specific cfm number that indicates excessive leakage?  If just a relative number, why not just use your manometer that you're using already instead of bringing another instrument?

If you have a 300 square foot bedroom, and the cfm is under 400 (roughly) the room becomes a low priority. Also, the Alnor works great around windows especially when the sun is out ( which plays havoc with IR) and windows treatments are present, you simply slide the 40 inch probe behind the curtains and wham, job is done. Last week I was in a home with a fireplace that had a cathedral ceiling, and I could run the probe from the top of the stone fireplace (11 feet high) and found that one side read 450 fpm from top to bottom. (103 cfm leakage). No ladder needed.

It doesn't work like you apparently think it does. Yes, the anemometer head gives you feet per minute of airflow (or some other velocity measurement), but to convert that velocity into a cubic footage measurement you need an exact measurement of the area that ALL of the air is flowing through. You don't have that measurement is you are simply placing the probe next to a piece of trim or a can light or a door gap.

Your method has applicability if you stick the probe into a duct of a known size and find the air velocity. FPM in a duct can be converted into CFM because the area is known. Look up "duct traverse" and look at how the method is presented by various folks. Jim Bergmann has a video or two on this topic using a Testo anemometer.

But, without know the area, you can't get a CFM figure...

Along side of a fireplace with an 11 foot ceiling which has a .25 inch opening along the outer edge. Dave, it is simple math. 9 cfm total at 450 fpm.

does the device have a read out display that shows the CFM #?

-Tammy    ilovewaterheaters.com

Hi Tammy,  The device gives you FPM, which is converted to CFM by multipling FPM by the area and dividing by 144.

You can also get types where you plug in the dimensions and it gives readings in cfm. 

I don't get how this would work for a BD test. The instrument seems to be designed for using in a duct. As it is testing air flow or realistically pressure and converting that number. How are these numbers relative to a induced pressure in a home in specific areas. Would it not read "leakage" in every corner due to flow whether there is a hole or not?

I could understand it working in a cavity such as a can light, duct or other openings communicating between conditioned and unconditioned space.

I do not understand how it would work along side the fireplace in an open space with charged air flowing and swirling from corners or what it would read behind the curtain.

An explanation would be greatly appreciated.  

After looking it up I see that it reads temperature of the probe at a set figure. It reads based on how much it cools down and displays that into data. no flow equals no cool down  It does not read pressure at all. Very cool device.

Still don't get how it works as described

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.  Home Energy Pros is sponsored by the Better Buildings Residential Network.

Latest Activity

David Baerg replied to Bachi Brunato's discussion Modeling a Gas Fireplace in Wrightsoft
"I would not include it.  Given that it is likely much less efficient than the gas furnace, you…"
16 minutes ago
Ryan Miller posted a discussion

First NC and now GA - Building Performance Associations taking shape

Hi All - Just a quick "this is what we're up to" for the community.The NC Building Performance…See More
23 minutes ago
Bachi Brunato posted a discussion

Modeling a Gas Fireplace in Wrightsoft

Any advice on how to factor a gas fireplace into a Wrightsoft Manual J model? Seems like it would…See More
24 minutes ago
Ryan Miller added a discussion to the group Job Board
Thumbnail

Wouldn't it make more sense to post jobs on a single board nationally?

Home Performance Coalition has one. Other organizations have one.  We have one for North Carolina. …See More
26 minutes ago
Profile IconRyan Miller and David M Cohen joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
29 minutes ago
robert jones posted a status
"Does anybody have audit tools for sale in the Albany NY area? Give me a call at 518-209-5912"
44 minutes ago
Bachi Brunato joined Kyle Brown's group
Thumbnail

Wrightsoft - Manual J / Manual D

If you use Wrightsoft to calculate loads or design ducts, you likely have questions.  Get answers…See More
7 hours ago
Colin Genge commented on Greg Labbe's blog post Technical Tape Desecration
"i don't have a picture of it, but my Honda Accord's windshield was replaced and it leaked…"
12 hours ago

© 2015   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service