I have a client who will eventually spend the money and have her ducts sealed and insulated, and the system properly balanced, but in the meantime her house is pretty hot on the 2nd floor. She has registers that were installed on the main supply trunk which have kept her basement cool, but she doesn't need the air to leak into her basement.

So, I remember seeing those magnetic register covers a few months back. Any suggestions on which covers actually work, and manufacturers of these register covers?

Thanks!

Patrick

Views: 523

Reply to This

Replies to This Discussion

Just use Saran wrap since it's only temporary.

Bob, I hear you, but this client is at least a little bit concerned with aesthetics, as they have a family member living in the basement. I am pretty sure that if I recommend saran wrap they will not be pleased with the recommendation, no matter how much it achieves their short term goal.

In my world, I'd put saran wrap (or similar) up all day long, but I am just living in that world of my clients.

I didn't figure anybody that lived in a basement would be picky, but I understand the need to please your customers. Since somebody is using that space why cut off all airflow? How difficult would it be to retrofit with butterfly dampers? How about stuffing something into the duct right behind the register? The problem with shutting off the registers is the whistling noise...

Good points Bob.

I guess I will just try to convince the HO to have the registers permanently closed off.

Thanks!

Remove the register and attach your choice of sealing material inside the register. Then reattach the register.  Saran Wrap, Duct Mask, Magnetic Material, CardBoard.  Cut to fit on site.  I've done this with supplies in the furnace room.  Returns in the furnace room, I use the magnetic on the outside.

Great advice.

Thank you John!

Patrick

Go to your local sign company-have them cut pieces of the material they use for magnetic vehicle signs.

Air pressure will most likely blow them off.

Interesting that you say that Bob. I had been pondering that.

It appears that I will just have to opt for permanently sealing the registers.

Thanks gents!

Good point,,,if you were sealing a high percentage of the registers in a house. I was thinking that they would do ok since they stand up to 70 mph wind, but that is shear strength, not direct pressure. But then again, how much pressure will there be-most of it would be relieved by the registers upstairs, no? And then it would be mostly a matter of shear strength. And far less than a speedy vehicle.

Maybe another alternative is to stuff the registers with foam board-maybe scraps from other jobs.

I like where you're going with this. I had considered the same thing (as there is a heck of a lot of scraps of rigid foam around the office here).

Many times we have used sign material and it won't blow of 99% of the time. And don't have the guy cut it as you can do that with a razor knife and a board or with a big pair of scissors.   You can get it is sheets or rolls, and a 12" roll will go a long way.  We have tried this on duct testing, but it doesn't work unless you depressurize - that's a whole other story on pressure/de-pressure in duct testing.  And you have to be careful of the little lever that opens and closes the louvers - cut a hole for it or cut the cover short of it.  And if you don't like that, sell her a couple of pieces of your duct testing tape if you still use it.

RSS

Welcome to Home Energy Pros

Welcome to Home Energy Pros – the unique digital community by and for those who work in the home energy performance arena.

Home Energy Pros was founded by the developers of Home Energy Saver Pro (supported by the U.S. Department of Energy) and brought to you in partnership with Home Energy magazine.  Home Energy Pros is sponsored by the Better Buildings Residential Network. Please honor our Guidelines

Featured Blogs

Seeking Innovation in Roofing Systems

Posted by Sarah OConnell on May 12, 2017 at 9:47am 0 Comments

Oak Ridge National Lab has partnered with GAF to host a technology challenge on roofing systems.  The challenge is part of the online crowdsourcing site, JUMP, and aims to identify innovation solutions for ensuring energy efficient and durable…

Continue

Top tips for maintaining an evaporative cooler

Posted by Kobus Niemand on May 4, 2017 at 3:30am 0 Comments

Evaporative coolers, also known as swamp coolers have become a top choice for anyone looking for an alternative cooling solution from their home or office. In the past, evap cooler technology was limited for use in large operations that have easy…

Continue

Congratulations to the 2017 Race to Zero Winners!

Posted by Home Energy Magazine on May 9, 2017 at 6:56am 0 Comments

The Ryerson University and University of Toronto team topped the …

Continue

Connecting the Dots: Real Estate and Home Performance

Posted by Home Energy Magazine on May 9, 2017 at 6:50am 5 Comments

A new type of conversation between REALTORS® and their clients is changing the real estate industry before our eyes. As homebuyers browse Zillow listings and spend…

Continue

Latest Activity

Andrew Etue added a discussion to the group Job Board
Thumbnail

Washington State Seeks Weatherization Field Monitor

Washington State Department of Commerce in Olympia, Washington is recruiting for a Weatherization…See More
15 hours ago
Andrew Etue joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
15 hours ago
Horace Douglas Hunt, Jr. posted a status
"Still looking to purchase a used RetroTec blower door - complete system. Anyone have something available?"
23 hours ago
Sean Lintow Sr replied to Luis Hernandez's discussion Solar panel leasing
"Sorry but no, not that big of a thing up here Biggest issue I see for most is everyone grid ties…"
yesterday

© 2017   Created by Lawrence Berkeley National Laboratory.   Powered by

Badges  |  Report an Issue  |  Terms of Service