I have a client who will eventually spend the money and have her ducts sealed and insulated, and the system properly balanced, but in the meantime her house is pretty hot on the 2nd floor. She has registers that were installed on the main supply trunk which have kept her basement cool, but she doesn't need the air to leak into her basement.

So, I remember seeing those magnetic register covers a few months back. Any suggestions on which covers actually work, and manufacturers of these register covers?

Thanks!

Patrick

Views: 422

Reply to This

Replies to This Discussion

Just use Saran wrap since it's only temporary.

Bob, I hear you, but this client is at least a little bit concerned with aesthetics, as they have a family member living in the basement. I am pretty sure that if I recommend saran wrap they will not be pleased with the recommendation, no matter how much it achieves their short term goal.

In my world, I'd put saran wrap (or similar) up all day long, but I am just living in that world of my clients.

I didn't figure anybody that lived in a basement would be picky, but I understand the need to please your customers. Since somebody is using that space why cut off all airflow? How difficult would it be to retrofit with butterfly dampers? How about stuffing something into the duct right behind the register? The problem with shutting off the registers is the whistling noise...

Good points Bob.

I guess I will just try to convince the HO to have the registers permanently closed off.

Thanks!

Remove the register and attach your choice of sealing material inside the register. Then reattach the register.  Saran Wrap, Duct Mask, Magnetic Material, CardBoard.  Cut to fit on site.  I've done this with supplies in the furnace room.  Returns in the furnace room, I use the magnetic on the outside.

Great advice.

Thank you John!

Patrick

Go to your local sign company-have them cut pieces of the material they use for magnetic vehicle signs.

Air pressure will most likely blow them off.

Interesting that you say that Bob. I had been pondering that.

It appears that I will just have to opt for permanently sealing the registers.

Thanks gents!

Good point,,,if you were sealing a high percentage of the registers in a house. I was thinking that they would do ok since they stand up to 70 mph wind, but that is shear strength, not direct pressure. But then again, how much pressure will there be-most of it would be relieved by the registers upstairs, no? And then it would be mostly a matter of shear strength. And far less than a speedy vehicle.

Maybe another alternative is to stuff the registers with foam board-maybe scraps from other jobs.

I like where you're going with this. I had considered the same thing (as there is a heck of a lot of scraps of rigid foam around the office here).

Many times we have used sign material and it won't blow of 99% of the time. And don't have the guy cut it as you can do that with a razor knife and a board or with a big pair of scissors.   You can get it is sheets or rolls, and a 12" roll will go a long way.  We have tried this on duct testing, but it doesn't work unless you depressurize - that's a whole other story on pressure/de-pressure in duct testing.  And you have to be careful of the little lever that opens and closes the louvers - cut a hole for it or cut the cover short of it.  And if you don't like that, sell her a couple of pieces of your duct testing tape if you still use it.

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Tom Mallard replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
"Right, that reinforces my understanding of how it works, I was after what to plug in for values in…"
1 hour ago
Hal Skinner replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
"Products like these dont have an R-rating. You still have to have the R-rated insulation to meet…"
2 hours ago
Graham Irwin replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Thanks for the input. The next question to ask is "how much cooling power is delivered in each…"
2 hours ago
Brandon Walton commented on Brandon Walton's blog post 12 Things Every Home Performance Contractor Should Have on Their Work Truck
"Totally off topic William, but yeah could use a bit more I suppose "
2 hours ago
William H Nickerson commented on Brandon Walton's blog post 12 Things Every Home Performance Contractor Should Have on Their Work Truck
"One more thing...you need a little more bend in that cap"
4 hours ago
Tom Mallard replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
"Sounds like the perfect, thin insulator adding enough thermal inertia to separate two masses and/or…"
4 hours ago
Hal Skinner replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
"OK Tom, I think I am on the last questionow,,,I think.  LOL Going under the building and…"
5 hours ago
Hal Skinner replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
"Tom, sorry for having to break this up but my responses I guess are too long. You talking about the…"
6 hours ago
Hal Skinner replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
" "
7 hours ago
Hal Skinner replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
"I guess I got too mlong winded ther, it cut me off. 1.  Spray the coating on the ducts, plenum…"
7 hours ago
Kurt Shafer replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Jan, Here are some facts. the 30 inch fan from Home Depot (not one I would recommend) is rated at…"
8 hours ago
Hal Skinner replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
"Hi Tom. It looks like I will have to start off most of my answers to questions with this…"
8 hours ago

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service