Can anyone recommend a low cost method for dealing with square recessed lights?   We find them often in soffits above kitchen sinks on eave exterior walls. In our experience:

  • There usually isn't enough head room to build a drywall or cement board box around them.
  • The prefabricated covers don't leave enough clearance around the larger housings and the headroom factor often prevents sealing covers anyway.
  • We've replaced the units with air-tight housings but they are expensive, often require new expensive trim, and since we can't find remodel housings, the headroom makes installing them very difficult.
  • We've also replaced them with surface mounts but that usually involves installing a junction box to extend the wiring, patching the ceiling hole, and drywall finishing since the surface mounts haven't been wide enough to cover the old hole.

Has anyone found air-tight inserts to fit square lights?  What about air-tight remodel housings?  Other suggestions?

Tags: Air, Lights, Recessed, Sealing

Views: 833

Reply to This

Replies to This Discussion

I don't think there is an easy answer for this. It might be cheaper to cut it out and replace with a can IC AT can and do the repair.

The other idea which I do not even know if I would recommend it is to remove the trim cover remove the glass spray paint the trim replace the bulb with an LED caulk or silicone the glass to the trim and caulk the trim to the drywall.

you mitigate air but not insulation. the unit itself is still functioning as it was but is now airtight. 

I like your second idea although there is still a fire hazard potential if we insulate around the fixture and someone replaces the bulb in the future.

agreed

Can you create an air barrier (5/8" drywall or 1/2" ply) at the ceiling level? eliminating the soffit, and the need to air seal, baffel, and insulate around the fixture?

This makes allot of sense access in those areas is always tight but if it could be done it makes everything easy.

As I mentioned with sealing the light and you point out lack of the ability to insulate is an issue. I would not insulate around it, but in the future will others show this reservation? The bulb would not bother me as the fixture has not been altered significantly and can still bleed heat into attic space. Will whomever cuts the caulking to access the bulb reseal it? Unknown and therefore not the best solution long term.

However as a cheap way to stop convection thermal bridging it works. Radiant is another story of course.

At times during these processes we need to weigh what is the best way and explore less effective methods based on budget.

for cost effectiveness and speed Georges suggestion is the best one. 

If it was my house, I'd be completely comfortable with the LED and insulating over the housing.  In fact, I'm debating offering it as a solution for clients so long as they are willing to accept the risk.  In this case, the days of incandescent lighting are numbered so the future risk is pretty negligible.

I think we try too hard to make everything idiot proof and risk free...it limits options and makes jobs too expensive.  Our window of opportunity to prevent climate catastrophe is short.  We need to make weatherization more affordable and part of that may require clients to accept some responsibility.  That could mean they can choose to have insulation blown over LED converted light housings, forgo dams around unused chimneys, have their house tightened beyond BPI standards without having to install continuous ventilation, streamline combustion safety to backdraft tests under normal conditions, etc.  Who's house is it anyway?

That's our standard approach but it's just too difficult in the eaves with a 3/12 pitch roof.

always hard to solve what you cannot see.

I use a method which for lack of a better term I call a Popsicle in tight areas such as this. I cut a piece plywood or drywall wide enough to cover most of the hole but slim enough to get between rafters. The length long enough to cover the hole plus about six inches. I attach a 1 x 2 to the board long enough to push to the edge on one side or the other which ever has better access. I crawl to the space bringing caulk, mastic or foam with me and a screw gun and some screws. Once I get to the area I load up the edges and run a bead on the far side as close to the opening as I can. I push the piece as far to the plate as I can squish down with stick and then run a screw into the Popsicle handle to secure it to the ceiling joist

It is not perfect but is ready for blown in insulation now.

I think, LED caulk is one of the alternative and best option which will be suitable for our budget. As per your interest you may select it. If I found any alternative options, I inform you at any time.

led reflector design

Extend the wire, remove box, insulate and use track wiring?  move to round recessed lights,   or look at some of the 2'x2' LED panels....

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Hannah Miller commented on Adam Flowers's blog post Comfort as a Selling Point
"Hello Adam! I hope you are still messages from this site. I just was forwarded your post and it…"
5 hours ago
Michael Dunseith replied to robert jones's discussion Should your local weatherization company be required to have someone BPI certified on their staff?
"Why the concern with airflow around heating and domestic pipes? Most are inside the envelope. What…"
7 hours ago
Tom White posted a video

Weatherization to Home Performance -- Tools & Tips for Developing For-profit Services

Are you a low income weatherization contractor looking to add home performance work you your services? The Home Performance Resource Center, Efficiency First, and NCAF present resources developed through expert industry engagement. While many of the…
9 hours ago
Jim Gunshinan posted a discussion

Tax Time Blues

There is a tax credit available to homeowners who have walls insulated. The credits were continued…See More
9 hours ago
Bruce Glanville replied to robert jones's discussion Should your local weatherization company be required to have someone BPI certified on their staff?
"I have been testing homes for my state utility as a baseline residential load data collection…"
9 hours ago
Stan Kuhn replied to Jim Gunshinan's discussion When your shower is in your kitchen...
"I think this is in the wrong Forum, it belongs in Hall of Shame.  One the dumbest ones…"
10 hours ago
Terrell posted a status
"Ebook version of my book Passive Buildings in Canada - detailed sections http://store.blurb.ca/ebooks/521524-passive-buildings-in-canada"
12 hours ago
Terrell posted an event

Boots on the Ground webinar at Toronto

March 10, 2015 all day
Passive Buildings Canada is pleased to be a sponsor and webinar host for BlueGreen Consulting…See More
12 hours ago

© 2015   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service