Was just looking for some input on different techniques for ensuring a permanent seal between a block foundation wall, and a 6 mil. poly barrier resting on a dirt crawlspace floor?  If one could referrence specific products that would aide also.  Thanks in advance for your input.

Views: 6058

Reply to This

Replies to This Discussion

I use CCA treated furring strips and mastic in the caulking tubes. Wrap the plastic around the strips, apply mastic, and fasten to the block with a hilti gun. Time consuming but it seems to work.

Tim,

I have used a recommend a product from crawlspacerepair.com called "Foundation Seal Tape".

It is a very strong and tacky double sided tape that is also waterproof.  I apply it continuously around the crawlspace about 3" below the top.  I use 15 mil poly that goes down the wall and then across the floor.

The tape seals and temporally mechanically holds the barrier in place until I ADD mechanical fasteners every 2 feet for  permanent bond.  

I highly recommend this product.

Tripp

I use the same mastic I use for sealing ducts, in my case Air Seal polymer adhesive.  Brush on a thick layer, then attach to the foundation wall as James describes.  I also use it for the laps across the crawlspace floor.  I don't trust the tape that Tim mentions.

I'm of the opinion that mechanically fastening the furring strips is a necessary, time consuming, and therefor costly step merely to insure the vapor barrier stays in place till the mastic dries. Once it dries, your not pulling the VB off without some effort.  If I come up with an easier alternative to temporarily hold the material in place, I'll test that theory and get back to you.

Tim,

I imagine you're using foam on the walls in the crawl space? If so, I have recently switched to foaming over the vapor barrier. It has been a very effective approach, assuming someone doesn't crawl through the space like a bat out of Hell and rip the barrier off the wall.

I run the poly up the walls (about 6 inches) and spray over the poly, and spray especially thick at the interface of the walls and the floor of the crawl.

Just my take on this, given personal experience and a genuine concern for the cost of projects getting out of control for the average HOs.

Don't use poly, use EPDM roofing material. Then you can use sprayfoam to seal.

Pat, about what are you paying per square foot of the EPDM membrane? I assume you use a roughly 60-mil product?

Thanks in advance!

Patrick

The EPDM can be purchased at 40 mils and 60 mils. I use the 40, over the past couple years we have paid between $0.80 and $1/sf for it. We buy black material. The white is much higher cost. It is very unlikely that it will see any sunlight or wear, so i see no reason to go thicker.
We usually spray foam fom the subfloor down on th EPDM and at east 4 ft in long the bottom of the wall and seal all joints. I am in upstate NY, 7000 HDD, so frost penetration under the wall governs how much of the floor we spray. I usually spray the whole floor if the space is less than 16 ft across. That is an arbitrary choice.

I do know of one job where the owners decided to tear down the existing house and put a year round residence in place of it after we did this work. he is a friend of mine, and he called to tell me demolishing the house was easy with an excavator until they got to the crawl space. Apparently the EPDM stretched enough so the excavator could not pull far enough to pull it loose from the block. In the end it pulled the blocks out still attached to the EPDM.

Impressive story Pat.

Thanks for the info on the EPDM!

I think you may have made a convert out of me (from poly vapor barriers to EPMD).

The foam manufacturer's make an extra sticky single part foam - same chemicals as the air sealing foam, different proportions.  We use Convenience Products Foam and they make one called Panel Foam.  This sticks the plastic up quite well, then we use it stick 2" board on the wall overlapping the plastic by a foot or so

i haven't heard of this before.  as far as I know all urethanes are 1:1 ratio, so i would sooner believe the resin/iso mix is 1:1, but the chemical reaction time is slowed a lot. 

have you gone back to one of these a month or further after install to see how the adhesion is? 

generally we get worse results with single component and dual component 'portable' or 'unheated' kits than we do with plural component heated kits.  those electric wraps for the cylinders are well worth the cost and hassle. 

Pat

I have no doubt that the ratio is 1:1, but not all are the identical formula.  We have been doing this for about 10 years and have had occasion to get back in to see up to 3-4 years later - no problem.  The 2 inch board is not extruded styrene but iso board with faces on it.

Any problems w/ VOC in crawl space during application or migration to home through floor?

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Tom Mallard replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group Radiant Control Coatings
"I'm interested in these coatings, have seen something in trade mags and know it's $$$ off…"
12 minutes ago
Jan E. Graveamker replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Hi, I have seen these fans in mounted in hall way ceilings, I have a couple of issues with…"
24 minutes ago
Jan E. Graveamker replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
33 minutes ago
Everblue posted a status
"Check out this video that Betty Saenz put together about Everblue's BPI training! Betty is a Realtor/EcoBroker in TX. http://bit.ly/1nSxcGJ"
43 minutes ago
David Eakin replied to Jamie Kaye's discussion Flickering LED lights
"I think the comments by Maria and Dennis have some merit for my own situation. I originally used…"
46 minutes ago
Ryan Rutledge commented on Hal Skinner's group Radiant Control Coatings
"Great idea.  Our company has a radiant control coating product so I think we can definitely…"
1 hour ago
Profile IconRyan Rutledge, Tom Mallard and 2 other members joined Hal Skinner's group
Thumbnail

Radiant Control Coatings

A group where people who work with radiant barrier coatings can let others know all of their uses.See More
1 hour ago
Tauran Ivall joined Sean Lintow Sr's group
Thumbnail

Best Practices (Residential)

Best Building, Retrofitting, or even Auditing Practices - what are they, what should change, what…See More
1 hour ago
Kurt Shafer replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Graham, Here are some facts Whole house fans preceded air conditioning by decades - example  -…"
2 hours ago
Brice Fawley commented on Brandon Walton's event Efficiency First AZ is Hosting Huge Meeting August 20th!
"This is a must attend. The future of the Home Performance industry in Arizona is a hot topic and we…"
2 hours ago
Graham Irwin replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Kurt, The "large fan" is a whole house fan moving anything from 1000-4000 CFM. By…"
3 hours ago
Kurt Shafer replied to Tom Conlon's discussion Whole House Fans - Love 'Em or Not?
"Graham, what "large fan" are you referring to?  I am fascinated by your comment…"
11 hours ago

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service