Recommended Intumescent Coatings for Polyurethane Foam Insulation

Hello folks.

I am looking for quality intumescent coatings for closed-cell spray and rigid foam insulation. 

I want to use the coatings for residential and small commercial applications.

Any advice?

Thanks in advance.

Patrick

Views: 1959

Reply to This

Replies to This Discussion

Hi Patrick,

As a consultant, I've specified products used by Demilec (http://www.demilecusa.com) for residential applications. They are manufacturers of open and closed cell spray foams, as well as intumescent coatings and other products. You can read about a few of their intumescent coatings on this page: http://www.demilecusa.com/technical-library/products

I'd recommend calling them for more information.

-Brady

Great, thanks Brady! I think this is exactly what I am looking for.

Patrick

this is a slippery slope. 

if the intumescents are tested on a foam product, then that system passes the thermal barrier requirement.  these systems are BRAND specific.  you need an ICC ESR report indicating the specific combination of a brand of foam with a brand of coating.  many foam manufacturers have relabeled a product called DC-315 as their proprietary product then tested that with their foam to get an ESR for the combination, but if you use the coating from a Demilec bucket on a Lapolla foam you technically do not have a code compliant product even if both manufacturers relabeled DC-315. 

if you Google DC-315 you can pull down data sheets from at least 6 foam manufacturers showing a combination of their foam and some relabeled variant of DC 315. you cannot get ESR's there though, you would have to go to the foam manufacturer to get those.   

Patrick,

Pat makes a good point, it definitely has to be a coating tested with a specific foam together as a system. I don't know if you are using high pressure spray foam or low pressure kits but if you are interested in a low pressure solution, Fomo Products' Handi-Foam has an intumescent coating Handi-Foam Ignition Barrier.


Learn more about it here: http://www.fomo.com/air-seal-accessories.aspx. 

There is a training module available from our partners at No Burn that goes more in depth about the type of coating you would need for your application.

Best of luck! Let me know if you have any questions.

-Leba

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.  Home Energy Pros is sponsored by the Better Buildings Residential Network.

Latest Activity

Dale Pickard replied to Rod Fox's discussion Does altitude affect AFUE? or just the input/output BTUs?
"Hans, The car manufacturer's are doing it with mass flow sensors and oxygen sensors…"
12 hours ago
Dale Pickard replied to Rod Fox's discussion Does altitude affect AFUE? or just the input/output BTUs?
"I was trying to avoid naming manufacturers, but I was going by the published information for the…"
12 hours ago
Eric Kjelshus replied to Rod Fox's discussion Does altitude affect AFUE? or just the input/output BTUs?
"I look at this not about AFUE,  but flue gas dewpoint.  If your burn rate is rotting the…"
15 hours ago
Bob Blanchette replied to Kirsten Richnavsky's discussion Crawl spaces and attics: OSHA to implement new rule on confined spaces
"Keeping HVAC equipment out of attics should be part of the new code. "
16 hours ago
Linda Wigington replied to Linda Wigington's discussion Weigh in - Honorable Mention? 2nd Base? Half-Way There? 50% Better? On the Path? in the group 1000 Home Challenge
"Nickie -  Good points. I think it is easy enough to flag or designate projects that achieve…"
17 hours ago
Morgan M Audetat replied to Rod Fox's discussion Does altitude affect AFUE? or just the input/output BTUs?
"Though Viessmann is relatively unique in the application of Lambda technology to condensing…"
18 hours ago
Lars olsen posted a blog post
yesterday
Eric Kjelshus replied to Rod Fox's discussion Does altitude affect AFUE? or just the input/output BTUs?
"The heat exchanger gets burnt out, if presser is to high or if mix is to rich, then I see holes in…"
yesterday

© 2015   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service