What do you guys think of these [URL="http://www.amazon.com/gp/product/B009EDGTXG/ref=as_li_ss_tl?ie=UTF8&camp=1789&creative=390957&creativeASIN=B009EDGTXG&linkCode=as2&tag=ecorenovorg-20"]low cost water heaters[/URL]?

The Good: At $225 they are even cheaper than a tank water heater!! Can use standard B vent, no expensive SS venting required. Works with 1/2" gas lines. Igniter runs off batteries, no electrical hookup required. Simple design, no electronic controls or inducer motors. Doesn't look like it needs a drain connection.

The Bad: Users complain poor temp regulation and questionable support after the sale. Efficiency isn't rated as high as more expensive models.

Views: 411

Reply to This

Replies to This Discussion

No edit option on original post, here is the correct link:

I've personally installed several of these. Yes, they're good units, and they work according to advertising when installed correctly. The problem is that some homeowners install it themselves and then complain that they don't work. But the "they" is the person not the heater, lol.

Anyway, Bob, to correct you, they cannot use B vent in many jurisdictions in N. America. That's because, like most gas or LP tankless water heaters, the exhaust contains corrosive condensate. After a few years of use with B vent, a hole will probably form, causing a noxious fume health hazard. Use Class III stainless steel, unless you want to redo the venting every 5 years or so.

The best installation guide I found for the 10L is on this page: https://gadgetsgo.com/Marey-10L-natural-gas-or-propane-indoor-water... . Scroll down to where it says Venting Guide.

You do need a drain connection for longer venting runs, but not for short ones.

Regarding support, sometimes I need to call the manufacturer Marey and never had a problem getting through. Try it yourself at 855-627-3955. It's their toll free number.

Why is B vent OK for standard tank water heaters but not the Marey? 80% and natural draft furnaces have been using b vent for decades, vent normally lasts 20+ years if installed correctly. The cost of The Cat III venting is more than the water heater. A condensing model @ $900 that uses ordinary PVC pipe starts making more sense.

Several tankless manufacturers have switched to allow for CPVC and PVC, for sure an easier and cheaper material.

Why is B vent OK for standard tank water heaters but not the Marey? 

Which ones? I don't know of any. That's because all tankless heaters produce condensate, and it's corrosive.

Anyway, many/most tankless manufacturers (Eccotemp, Rheem, Paloma, Rinnai) also require the Class III SS on many of their current models. It's not just Marey.

RSS

Featured Forum Discussions

BPI Anaylist and installers

Started by Larry R Waters in BPI. Last reply by Quinn Korzeniecki 8 hours ago. 1 Reply

What causes a temperature plane in a home

Started by Energy Wise Solutions in HVAC. Last reply by Brad Cook yesterday. 6 Replies

Velocity Pressure Testing

Started by Horace Douglas Hunt, Jr. in General Forum. Last reply by Horace Douglas Hunt, Jr. Apr 15. 2 Replies

Videos

  • Add Videos
  • View All

Latest Activity

Profile IconManuela L Heyn and Paul Nagel joined Home Energy Pros
2 hours ago
Bill Spohn replied to Eric Sperline's discussion Wanted: Energy Auditing Equipment for sale in the group Energy Auditing Equipment for Sale, Trade or to Purchase
"If you choose to buy new, give TruTech at call at 1-888-224-3437 option 1"
4 hours ago
Home Energy Magazine's blog post was featured

The Legends of Home Performance

A project long in the making, we're happy to finally reveal some of our Legends of Home Performance…See More
5 hours ago
Quinn Korzeniecki replied to Larry R Waters's discussion BPI Anaylist
"Hi Larry, We're glad you're reaching out to hire some BPI folks! You can also submit…"
8 hours ago
Larry R Waters posted a discussion

BPI Anaylist

Industry leader in the north bay area California. Looking for experienced professionals and…See More
16 hours ago
Larry R Waters joined Diane Chojnowski's group
Thumbnail

Job Board

This group is for posting jobs related to all aspects of the home performance industry including…See More
16 hours ago
John Nicholas replied to Jim Fowler's discussion TREAT modeling of mid-rise apartments low heating load
"So why is tenant behavior significantly different in this building?"
17 hours ago
Jim Fowler replied to Jim Fowler's discussion TREAT modeling of mid-rise apartments low heating load
"Hi John - I'm strictly modeling the entire building, not individual units. I'm looking…"
17 hours ago

Home Energy Pros

Welcome to Home Energy Pros – the unique digital community by and for those who work in the home energy performance arena.

Home Energy Pros was founded by the developers of Home Energy Saver Pro (supported by the U.S. Department of Energy) and brought to you in partnership with Home Energy magazine.  Home Energy Pros is sponsored by the Better Buildings Residential Network. Please honor our Guidelines

© 2017   Created by Lawrence Berkeley National Laboratory.   Powered by

Badges  |  Report an Issue  |  Terms of Service