I'm glad to see LED fixtures finally becoming mainstream in the local big box stores. Purpose built fixtures make more sense than trying to make LED's look and work like A19 lamps. Here's an example of the fixture I saw at the local Home Depot today:

http://www.homedepot.com/p/Lithonia-Lighting-Versi-Lite-7-in-White-...

I'll post more photos/findings once I get it hooked up.

Tags: Fixture, LED, Light

Views: 691

Reply to This

Replies to This Discussion

I too had the offset issue, the 2nd screw went direct into the ceiling joist. Oddly the smaller boxes seem more common than the larger ones in ceiling use.

There are 50 point LED's (possibly cree's devices) on the board.  The large black chip is most likely the a chip whose function is sensing dimming on the incoming power signal and translating that to the equivalent on/off duty cycle for the LED's.  Just a couple of small surface mount chip caps.. so no electrolytics to fail.  But heat is a silent killer for most IC's... if the fixture is hot - U1 is gets my second vote for the most failures.  First goes to the movistor.  The LED's are likely to suffer a "fading" effect and slowly become less effective. Four or five years from now you might notice a difference if you compare it against an identical fixture.  But then anyone expect a CFL last five years - with lots of use, dimming, and turning on/off....

At $30 I expect it to last, hopefully they stand behind their warranty for 5yrs if it doesn't. If it fails after 5yrs LED tech will be fully mature by then and newer better fixtures will be out. Fixtures designed for LED from the start have a lumen/watt advantage since they can take advantage of the native directional properties of LED. Fixtures also have more thermal management options compared to A19 retrofit laps, and as you said heat is the enemy of the electronics/driver circuit.

IMHO the best is yet to come for LED fixtures, I'm sure they are working on things we haven't even though of. Fixtures is what will revolutionize the LED lighting industry, not A19 replacements...

Generally based upon the needed requirements, The mode of selection will be depended. In these aspects, We must consider the high quality of LED strips which will help us to give more brightness while compared to the normal one.

reflector design

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Profile IconBrendan Reid, Brian Keech, Bob Reuther and 1 more joined Home Energy Pros
4 minutes ago
Hal Skinner added a discussion to the group The RCC Classroom (Radiant Control Coatings)
Thumbnail

Improved acoustics

Some RCCs claim to improve acoustics .  Here are a few examples of ours.…See More
23 hours ago
Patrick Carter replied to Patrick Carter's discussion Minneapolis Blower Door & Test Equipment for Sale! in the group Energy Auditing Equipment for Sale, Trade or to Purchase
"As of yesterday 09/19/2014, the equipment has been sold..."
yesterday
Hal Skinner replied to Hal Skinner's discussion An example of what an RCC can do with no R- insulation in the walls.
"Mornin Brett. 90 to 85, yes a slight variance there.  Same ASTM test, different scientists,…"
Friday
Bret Curry replied to Hal Skinner's discussion An example of what an RCC can do with no R- insulation in the walls.
"Great information Hal. It appears the thermal emissivity in your test was .85 rather than .90. Are…"
Friday
Juan Roca commented on Dale Stephens's blog post LED Lighting - Garage Door opener interference
"Hi,There is a real problem with remote controls and LED lights. However, there is a solution in the…"
Friday
Profile IconJuan Roca and Elizabeth Coe joined Home Energy Pros
Thursday
Casey Gesell posted videos
Thursday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service