Are there suggestions out there as to the best way to insulate newly installed speakers!  I have been working to improve the  tightness of my 22 year old home but after that big effort, I installed 10 speakers in 5 rooms.  This, as one might suspect, has resulted in several holes leading from unconditioned spaces to conditioned spaces. Some folks say just drape insulation over the new speakers while other say build a box to protect the innards of the speakers from fiber glass, dust, etc. The latter is supposed to enhance the quality of the music emanating from the speakers but there are many opinions out there!

Views: 4434

Reply to This

Replies to This Discussion

Build a box, air seal & mound insulation over them equivalent to what's around them

As for acoustics - depends on speakers  - base, etc... as these are probably regular 3 to 5 ways it probably wont help much but you might want to check w/ manufacturer for suggestions- as for long life & keeping crap out - box em

Thanks, Sean!  I have been looking for "ready made" boxes w/o much luck, mostly 'cause I wanted to see how they look and how they were constructed so I might have a template to follow.  I have contacted my 3 manufacturers, some who say use a box and others make no mention of a need for a box.  What do you think about a Styrofoam box with 1.5 to 2 " thick walls, then covered with insulation?

I would dare to say it doesn't matter what the box is made of - drywall or foam are easiest. I say air seal that box, insulate over it and call it good.

Just wanted to thank all of you who responded to my inquiry and I am looking for Styrofoam so I can start my box construction.  Some of my speaker instructions state a cubic foot of volume is required to maximize sound output while others don't seem to even address this issue? Is htis a case of what is good for the goose is good for the gander?.  All will get boxes over time, I guess, and then I shall cover them with insulation!

Cheers.

John

have you heard of TenMat covers?  They are designed for recessed lights, but would work for speakers.  they are not overly expensive and are very easy to install.  http://www.tenmat-us.com/index.html 

Thanks, Pat, for your time and your response.  I will visit that site and see what they have to offer! Cheers.

John

Pat, John again. Have you used this product for in-wall speakers and if so, how did you affix them to a vertical wall?

I only use then in attics. Framing the cavity is most effective for walls.

Thanks for your response, Pat.  Do you feel it is necessary for me to frame wall-mounted speakers when the backsides are open to the attic?  I am leaning toward just foam spraying the covers to the walls?     

We use plural component foam (2 part foam), not the foam from an aerosol can (single component foam) so the foam sets up fairly quickly and it binds to the TenMat covers very well. I could set a cover over a speaker on a vertical surface and spray it to support it with this system as long as I can access the speaker from an attic or similar surface. This will not work with single component foam, and would not work with 'froth packs' in situations where ambient or surface temperature is below 60. I can do it at temperatures as low as 30 with a foam rig.

For the typical 2-way (meaning 2 speakers, tweeter and woofer) in-wall rectangular speakers that are designed to fit in between a 2x4  16"oc wall cavity, boxing in an enclosure will generally improve the bass response. Simply place 2 pieces of wood between the studs top & bottom of speakers  and seal with caulk. Depending on the drywall, you may want to add additional screws to minimize any wall vibration caused by the woofer For round in-wall which are typically used in ceilings (the tweeter is mounted inside the woofer cone)you need to box them in both for acoustics and preventing insulation. Between floors with no access may prevent you from making an enclosure. Keep in mind electrical low voltage codes do require you use speaker wire rated for in-wall and I would recommend 14 gauge if running any distance or 16 gauge for short distances. Speakers are polarized so make sure the wire is marked

Jose, Thank you for your helpful response.  It was very comprehensive, the kind of help I am needing. BTW, if one is to reverse the polarity of the speaker wire, what kind of effect is one likely to notice? Scratchy, muddy sound, ???

Cheers.

John

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Richard Vito joined Sean Lintow Sr's group
Thumbnail

Best Practices (Residential)

Best Building, Retrofitting, or even Auditing Practices - what are they, what should change, what…See More
24 minutes ago
Richard Vito joined James Sayers's group
Thumbnail

Marketing Energy Efficiency

Sharing ideas, tools and examples of promoting energy efficiency to consumersSee More
25 minutes ago
Richard Vito joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
26 minutes ago
Richard Vito joined Kyle Brown's group
Thumbnail

Wrightsoft - Manual J / Manual D

If you use Wrightsoft to calculate loads or design ducts, you likely have questions.  Get answers…See More
27 minutes ago
Richard Vito joined allen p tanner's group
Thumbnail

Energy Auditing Equipment for Sale, Trade or to Purchase

Discuss the pros and cons of the equipment you are interested in prior to purchase. Post equipment…See More
28 minutes ago
Jim Gunshinan commented on Jim Gunshinan's blog post Energy Upgrade California—Up Close and Personal
"I had a revelation while attending Bruce Manclark's session of duct leak testing at the Energy…"
14 hours ago
George J. Nesbitt commented on Jim Gunshinan's blog post Energy Upgrade California—Up Close and Personal
"Blower Door; the 2007 test was a depressurization test, and the 2014 a pressurization test, which…"
15 hours ago
George J. Nesbitt replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Plan, plan, plan, plan. The 1st step to is to understand the house, how it's built, the…"
15 hours ago
George J. Nesbitt posted an event

High Performance Windows - A Panel of Experts at Pyramid Alehouse`

April 26, 2014 from 3pm to 5pm
Join a lively panel discussion on high performance windows. We'll cover some basics, as well as…See More
16 hours ago
Kaushal Bharath Raju replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Hi David, Thanks for pointing out Martin Holiday's article. I do not wish to engage in the…"
16 hours ago
Profile IconAdam Penberthy, Scot Davidson and j jarvella joined Home Energy Pros
16 hours ago
David Eakin replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"More food for thought on this subject - read this (fairly) recent blog by one of the most respected…"
22 hours ago

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service