Are there suggestions out there as to the best way to insulate newly installed speakers!  I have been working to improve the  tightness of my 22 year old home but after that big effort, I installed 10 speakers in 5 rooms.  This, as one might suspect, has resulted in several holes leading from unconditioned spaces to conditioned spaces. Some folks say just drape insulation over the new speakers while other say build a box to protect the innards of the speakers from fiber glass, dust, etc. The latter is supposed to enhance the quality of the music emanating from the speakers but there are many opinions out there!

Views: 23260

Reply to This

Replies to This Discussion

From techstreet -- holder of some of the UL documents.... about UL-1715

"This test method is intended for use in the evaluation of the flammability contribution of wall materia l assemblies, ceiling material assemblies, or both, exposed to early fire growth under specified room fir e exposure conditions. The effectiveness of fire barrier materials as protection for other combustible materials or components within the assembly is of primary interest for this evaluation."

The point of suggesting to look for UL1715 and the ASTM numbers is that it might be that other good building materials would be found that could do a better job for John.  That was the reason for suggesting keywords for searches.

The Tenmat hats themselves provide the flame spread,  the fire stop foams/sealants, just cover the cases where flames might seep under the hats and into the attic.   They also stop the hats from rattling and dancing around in the attic when loud rock and roll is played  :-)

good point on the dancing. 

my only concern is that folks dont get the impression there are fire safe foam's out there.  if you ignite an piece of FS 25 foam and take the flame source away, the foam will self extinguish.  But, the tech data sheets the foam manufacturers provide will have footnotes saying their foam requires a 15 minute thermal barrier between the foam and the people.  that's becasue foam has a low self ignition temperaturte, and it is very good at holding heat in.  it doesn't take long for foam to burn when it is exposed to heat in excess of 450 degrees. 

RSS

Featured Forum Discussions

What causes a temperature plane in a home

Started by Energy Wise Solutions in HVAC. Last reply by Peter Krych yesterday. 4 Replies

Velocity Pressure Testing

Started by Horace Douglas Hunt, Jr. in General Forum. Last reply by Horace Douglas Hunt, Jr. Apr 15. 2 Replies

Videos

  • Add Videos
  • View All

Latest Activity

Crosbey Archery posted a blog post
1 hour ago
Profile IconRon Sarrick and Alana Barnett joined Home Energy Pros
14 hours ago
Jim Fowler posted a discussion

TREAT modeling of mid-rise apartments low heating load

Does anyone have experience using TREAT to model mid-rise (3-story) apartment buildings with…See More
yesterday
Peter Krych replied to Energy Wise Solutions's discussion What causes a temperature plane in a home
"I also should have asked where the furnace was located,basement,1st or 2nd floor. In any case the…"
yesterday
Profile IconJim Fowler, Jennifer Flanagan, Debra Smit and 2 more joined Home Energy Pros
yesterday
Eric Sperline added a discussion to the group Energy Auditing Equipment for Sale, Trade or to Purchase
Thumbnail

Wanted: Energy Auditing Equipment for sale

I am looking to buy a door frame panel that will accept a duct blaster fan.  I don't need the…See More
yesterday
Energy Wise Solutions replied to Energy Wise Solutions's discussion What causes a temperature plane in a home
"This scenario occurs in the Winter Months.  It is warmer upstairs.  This is a forced Air…"
Friday
Peter Krych replied to Energy Wise Solutions's discussion What causes a temperature plane in a home
"Are these winter conditions, is it colder or warmer upstairs, is it forced air or radiant heat? It…"
Thursday

Home Energy Pros

Welcome to Home Energy Pros – the unique digital community by and for those who work in the home energy performance arena.

Home Energy Pros was founded by the developers of Home Energy Saver Pro (supported by the U.S. Department of Energy) and brought to you in partnership with Home Energy magazine.  Home Energy Pros is sponsored by the Better Buildings Residential Network. Please honor our Guidelines

© 2017   Created by Lawrence Berkeley National Laboratory.   Powered by

Badges  |  Report an Issue  |  Terms of Service