Are there suggestions out there as to the best way to insulate newly installed speakers!  I have been working to improve the  tightness of my 22 year old home but after that big effort, I installed 10 speakers in 5 rooms.  This, as one might suspect, has resulted in several holes leading from unconditioned spaces to conditioned spaces. Some folks say just drape insulation over the new speakers while other say build a box to protect the innards of the speakers from fiber glass, dust, etc. The latter is supposed to enhance the quality of the music emanating from the speakers but there are many opinions out there!

Views: 22478

Reply to This

Replies to This Discussion

Build a box, air seal & mound insulation over them equivalent to what's around them

As for acoustics - depends on speakers  - base, etc... as these are probably regular 3 to 5 ways it probably wont help much but you might want to check w/ manufacturer for suggestions- as for long life & keeping crap out - box em

Thanks, Sean!  I have been looking for "ready made" boxes w/o much luck, mostly 'cause I wanted to see how they look and how they were constructed so I might have a template to follow.  I have contacted my 3 manufacturers, some who say use a box and others make no mention of a need for a box.  What do you think about a Styrofoam box with 1.5 to 2 " thick walls, then covered with insulation?

I would dare to say it doesn't matter what the box is made of - drywall or foam are easiest. I say air seal that box, insulate over it and call it good.

Just wanted to thank all of you who responded to my inquiry and I am looking for Styrofoam so I can start my box construction.  Some of my speaker instructions state a cubic foot of volume is required to maximize sound output while others don't seem to even address this issue? Is htis a case of what is good for the goose is good for the gander?.  All will get boxes over time, I guess, and then I shall cover them with insulation!

Cheers.

John

have you heard of TenMat covers?  They are designed for recessed lights, but would work for speakers.  they are not overly expensive and are very easy to install.  http://www.tenmat-us.com/index.html 

Thanks, Pat, for your time and your response.  I will visit that site and see what they have to offer! Cheers.

John

Pat, John again. Have you used this product for in-wall speakers and if so, how did you affix them to a vertical wall?

I only use then in attics. Framing the cavity is most effective for walls.

Thanks for your response, Pat.  Do you feel it is necessary for me to frame wall-mounted speakers when the backsides are open to the attic?  I am leaning toward just foam spraying the covers to the walls?     

We use plural component foam (2 part foam), not the foam from an aerosol can (single component foam) so the foam sets up fairly quickly and it binds to the TenMat covers very well. I could set a cover over a speaker on a vertical surface and spray it to support it with this system as long as I can access the speaker from an attic or similar surface. This will not work with single component foam, and would not work with 'froth packs' in situations where ambient or surface temperature is below 60. I can do it at temperatures as low as 30 with a foam rig.

For the typical 2-way (meaning 2 speakers, tweeter and woofer) in-wall rectangular speakers that are designed to fit in between a 2x4  16"oc wall cavity, boxing in an enclosure will generally improve the bass response. Simply place 2 pieces of wood between the studs top & bottom of speakers  and seal with caulk. Depending on the drywall, you may want to add additional screws to minimize any wall vibration caused by the woofer For round in-wall which are typically used in ceilings (the tweeter is mounted inside the woofer cone)you need to box them in both for acoustics and preventing insulation. Between floors with no access may prevent you from making an enclosure. Keep in mind electrical low voltage codes do require you use speaker wire rated for in-wall and I would recommend 14 gauge if running any distance or 16 gauge for short distances. Speakers are polarized so make sure the wire is marked

Jose, Thank you for your helpful response.  It was very comprehensive, the kind of help I am needing. BTW, if one is to reverse the polarity of the speaker wire, what kind of effect is one likely to notice? Scratchy, muddy sound, ???

Cheers.

John

RSS

Featured Forum Discussions

Glass Block Windows

Started by Ken Kalke in Best Practices. Last reply by Sean Lintow Sr on Saturday. 1 Reply

What's the Most Profitable HVAC Job for Your Company?

Started by Wayne Melancon in HVAC. Last reply by Ken Kalke on Friday. 1 Reply

Lighting replacement - 300 watt LED flood light

Started by Mary Sinkler in General Forum. Last reply by Eric Kjelshus on Friday. 1 Reply

EZ Green Home is Hiring!

Started by Chloe Chapman in General Forum Jan 5. 0 Replies

Videos

  • Add Videos
  • View All

Latest Activity

tedkidd replied to tedkidd's discussion Home Performance is Failing - let's turn that around?
"Thank you Ira! We need more stories like yours to hold the evidence of harm to the faces of…"
8 minutes ago
Profile IconPaul Mausteller, Mark Freeman and Bruce Fillmore joined Home Energy Pros
17 minutes ago
Ira Eisenstein replied to tedkidd's discussion Home Performance is Failing - let's turn that around?
"I have been a home inspector since 2003 and evolved into energy related issues and became a home…"
3 hours ago
Ira Eisenstein liked tedkidd's discussion Home Performance is Failing - let's turn that around?
3 hours ago
Bruce Fillmore joined Diane Chojnowski's group
Thumbnail

Home Energy Pros on Twitter

We've created a twitter list of members of Home Energy Pros who tweet about home performance and…See More
4 hours ago
Bruce Fillmore posted photos
5 hours ago
Sean Lintow Sr replied to Ken Kalke's discussion Glass Block Windows
"Well as most I know (if not all) wont meet the energy code - none and for those that do opt…"
Saturday
Steve Gadsby posted a photo
Friday

Home Energy Pros

Welcome to Home Energy Pros – the unique digital community by and for those who work in the home energy performance arena.

Home Energy Pros was founded by the developers of Home Energy Saver Pro (supported by the U.S. Department of Energy) and brought to you in partnership with Home Energy magazine.  Home Energy Pros is sponsored by the Better Buildings Residential Network. Please honor our Guidelines

© 2017   Created by Lawrence Berkeley National Laboratory.   Powered by

Badges  |  Report an Issue  |  Terms of Service