Handling An Interesting Crawl Space

Replies to This Discussion

Permalink Reply by Bruce Navin on April 17, 2012 at 5:38am

Considering the small size of the job, is there a minimum number that the insulation guy is going to charge for the job? I would determine that with different comparisons of thicknesses of the foam.

Does the crawl space have a floor? Is it ventilated? Do you have moisture coming up? 

• ▶ Reply

Permalink Reply by Patrick Michaelyan on April 17, 2012 at 5:53am

Hello Bruce.

Slab floor. Ventilated like you've never seen before. There are large openings at the perimeter for easy access to the space. The accesses are closed up with steel gates (of the aesthetic kind), so sealing up the space at the walls is not an option. No moisture coming up.

No minimum charge for job, just "get it right." My goal is to get the homeowner the best bang for his buck. This is why I'd like to get the flash coat of foam (about an inch) to the floor.

Thanks Bruce.

• ▶ Reply

Permalink Reply by Bruce Navin on April 17, 2012 at 6:28am

If cost isn't an option, why not go with a full thickness of foam and get rid of the f/g? Eventually, moisture will gather in the f/g, wire supports will fail and the homeowner will have a problem again.

• ▶ Reply

Permalink Reply by Patrick Michaelyan on April 17, 2012 at 6:34am

You raise a very legit point Bruce, but then we are also talking about a job cost near $2,000 versus $600. Also, this means that we'd be throwing out good insulation, and I hate "wasting" things.

Also, won't the house wrap serve to significantly reduce the moisture build-up in the fiberglass?

• ▶ Reply

Permalink Reply by Bruce Navin on April 17, 2012 at 6:56am

I'm sure the house wrap will reduce the moisture penetration substantially, as long as it is installed properly. But I don't know if it will prevent all moisture penetration over a period of years. Especially if there are critters involved. Any chance of bats nesting under there? I am flying blind here a bit, but if the h/o paid for decorative iron gates for his crawl space, I'm not sure that he would flinch at an informed proposal for foam for an additional $1400.00.

If I were you, I would lay down options for him to decide, and tell him what you would do if it were your home, and why; while setting aside the cost considerations. People are not always easy to read, and I have often been surprised when homeowners bite on quality over cost after a good sales presentation. Who knows, he may like the foam so much that he calls you back to do the whole attic next year.  

• ▶ Reply

Permalink Reply by Patrick Michaelyan on April 17, 2012 at 7:00am

Good points Bruce.

I'll give it a shot.

One last issue: the ducts in the floor. I was going to have rigid insulation installed below the flex duct (the ducts sit just above the underside of the floor joists). Any suggestions? Thanks!

• ▶ Reply

Permalink Reply by Bruce Navin on April 17, 2012 at 7:05am

That makes sense to me, I would hit the rigid foam with the foam as you pass by, mainly to seal the edges and have a uniform finish.

• ▶ Reply

Permalink Reply by Carlos Espinoza on April 19, 2012 at 9:28am

Here's a great article for your resource: http://www.greenbuildingadvisor.com/blogs/dept/musings/building-unv...

Also, will there be any negative fumes emitted from the spray foam application?  http://www.greenbuildingadvisor.com/community/forum/green-products-...

• ▶ Reply

Permalink Reply by Patrick Michaelyan on April 20, 2012 at 6:47am

Thanks for the article Carlos.

The new product I'm using is supposed to emit no VOCs that would be considered negative fumes. In the past that has been one of my main concerns with respect to spray foam.

Patrick

• ▶ Reply

Permalink Reply by Cory Chovanec on April 20, 2012 at 5:44am

Sounds like a winner to me, you can skip the wire supports the house wrap should support the insulation just fine. Another option would be to skip the fiberglass and spray foam, and fasten ridgid foam (thermax) to the joists then dense pack with cellulose. The foam and dense pack is just a sweet way to go. You reduce the thermal bridging of the joists, get a good air seal, and have a nice finished R-value.

• ▶ Reply

Permalink Reply by Patrick Michaelyan on April 20, 2012 at 6:51am

Cory, the approach you mention is the balls! I typically do just what you recommend. In this case I want to avoid tossing the fiberglass, and the homeowner is concerned with accessing the pipes, ducts, etc.

Thanks for the advice Cory!

• ▶ Reply

Permalink Reply by Patrick Michaelyan on April 20, 2012 at 6:57am

Cory, for future reference, when you go the rigid and dense-pack cellulose route do you also hit the main penetrations through the floor with foam sealant, or would you just consider that over-redundant?

And, same question with respect to fiberglass and rigid (vs. cellulose and rigid).

Patrick

• ▶ Reply

• ‹ Previous
• 1
• 2
• Next ›
• Page