"You note overheating on the south side (naturally.) Assuming the typical roof overhang of…"
Funky Duct Test
Last week I was doing a rough-in w/air handler installed duct test. I taped all the supply boots and installed the fan to the return grill just as always. When I set up the manometer, I noticed a pressure reading of 135Pa, this without the fan being turned on. If I disconnected the hose from the manometer, pressure fell to zero. Assuming I had done something to cause this I checked and rechecked everything, even installed fresh batteries. Finally, I moved the hose to another supply boot, this resulted in a proper reading so I went ahead with the test.
Does anyone have any idea what was going on to give such a reading? Let me know if you need more information. Thanks for help solving this perplexing question.
Views: 254
Replies to This Discussion
-
Permalink Reply by David Meiland on -
Hard to see how there could be +135 in one supply duct without at least some positive reading everywhere else. Maybe someone accidentally (?) tied a bath fan into that duct.......
-
Permalink Reply by Bill Bennett on -
No power to the house at time of testing.
-
Permalink Reply by Glen Gallo on -
someone stepping on the hose?
-
Permalink Reply by Bill Bennett on
-
No.
-
Permalink Reply by Bud Poll on -
I would tend to agree with Glen, as a blocked tube will clock up rather fast. If there is still a pin hole I suspect the pressure would stabilize at some point, although I'm not going to test it. It could have been a kink somewhere that unfolded when you moved the hoses. If it was a positive pressure the block was on the input. If negative it would have been on the reference, DG700 at least.
Bud
-
Permalink Reply by Bill Bennett on
-
I just submitted this to the Energy Conservatory. If I get something useful back from them, I'll post it here.
-
Permalink Reply by Bill Bennett on
-
As promised, I asked the folks at The Energy Conservatory about my funky duct test results. Paul Morin, a Technical Sales Specialist suggested that such a situation could occur if the hose is stopped up or perhaps was up against insulation in the supply boot. He went on to say; "You can simulate a pressure this high by putting your finger over an open tap on the DG-700 gauge. It is harder to reproduce a pressure that high with a long length of hose attached, but you would see pressures that high if some debris is plugging the hose. You also will see pressures that high if the hose is pinched, stepped on or if there is water in the hose."
I believe that the end of the metal probe must have been up against the boot insulation, probably when I taped the hose to secure it. The resulting restriction of air caused the errant reading.
Thanks to everyone who offered a suggestion.
-
Permalink Reply by Matt Marshall on -
Something else to look out for. If you use the metal probe to punch through the plastic tape you can actually punch a hole in the plastic tape which will cover the end of the probe. I've had this happen to me and it caused some temporary confusion.
Home Energy Pros
Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy, under the American Recovery and Reinvestment Act) and brought to you in partnership with Home Energy magazine.
Latest Activity
Patrick Michaelyan replied to Patrick Michaelyan's discussion Hot Upper Stories"Thanks a lot Ed. And thanks to all who have added their two cents.
I think I know where to take…"
Ed Minch replied to Patrick Michaelyan's discussion Hot Upper Stories"We have successfully treated this same problem in perhaps 1000 of this same house in the…"
Craig Savage commented on Craig Savage's video
What is a Heat Pump Water Heater
"Hello Tom
We are working with A.O. Smith, GE and Stiebel Eltron on a Building America task to…"
Tom Delconte commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Craig: I was serious, since my propane price jumped from .98 to 1.85! according to everyone the GE…"
Ben Jacobs replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"I think that government support for good ideas results in major benefits over the long haul.
Please…"
Craig Savage commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Hello Tom
Not sure if you are being sarcastic, but a serious answer would be that GE is selling…"
Tom Delconte commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Craig: do you have a diagram of one that will run longer than one year? They don't really seem…"
Cory Chovanec replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"All good points brought up. My advice is not to leave the lights. When you said halogen I think…"
Jon Haehnel replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"The first 2 answers by Tom and Sean jive with my thinking and experience. Thank you Don for…"
Tom Smith replied to Patrick Michaelyan's discussion Hot Upper Stories"The most bang for your buck will come from airsealing the attic plane and sealing the…"
John Rising replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"Hi Bachi,
We have done many projects where we have installed boxes around recessed lights to…"
© 2013 Created by Lawrence Berkeley National Laboratory.
