Good day everyone,

While performing an audit and blower door test, we came across a french door (pics attached) that, of course, was hemorrhaging air. The homeowner also complained about insects getting in around the door (surprising, of course).

We think we can air seal the perimeter with good weatherstripping, but are at a total loss for what to do where the doors come together. Both sides are operational and used. The doors are fiberglass, so adding weatherstripping between them is not practical. We thought about using some v-stripping on both sides, but then we run into the same problem of how to attach it since adhesive would wear out and screws are impractical.

As you can see in the photos, the homeowner used foam tape, but the gap is simply too big and the adhesive not strong enough to handle the sheer forces of the doors opening and closing.

Any advice would be quite welcome.

Views: 2491

Reply to This

Replies to This Discussion

It looks like the dor is a bit cammed. Close at he top and spread at the bottom. The door itself looks as if it needs to be realigned from the photo. It is always hard to tell the exactly from a photo.

I got to agree with Gallo, fix the fit first & then make sure the secondary door locks work properly / not to much slop & then fix the weather stripping with the type that is meant for that door

It looks like the door frame was not properly aligned during installation. I just replaced my old slider doors with french doors a couple months ago. I had the opposite problem. My doors would not shut. Fortunately, I had a construction guru installing my doors and he did some tweaking on the outer door frame to get it just right. I would have the homeowner contact the construction company that installed the door to reorient the frame properly. If the homeowner installed the door, I would recommend two options. 1) Hire an experienced construction company to correctly orient the door frame, or 2) Try using wood shims to the outer lower edges of the the door frame to force it towards the center. Either way the door frame will need to be re-caulked for air sealing. Hope that helps and good luck. No one wants air or bugs pouring in.

Energy Info

Looks like a low end french door from a big box store.  Upgrade to a better door, Andersen, Marvin, etc

quality of the door does not matter with poor installation.

First I would test the hinges to make sure the are all screwed in and not loose I would make sure the stop on the non operable side is aligned correctly  and determine if any gains are made by adjusting. my guess from the photo no but process of elimination and ease of repair dictate I try these two first.

 Using a level I would determine which side is my biggest problem left right top or bottom

If it is the top I would guess a nail or screw pulling it up in the middle I would remove molding and cut the screw or nail (possible and best case as it is easy but not at all likely as it should be cammed the other way)

If it is the bottom it would be sagging in the middle and I would shim it up (not likely at all but always worth looking)

 If left or right I would try adjusting the hinges and or shimming from the inside before going for major surgery.  one.door is most likely worse than the other which can be seen by using a level. I would adjust and observe.(probable)

If all of the above fails to yield results I would pull it out and make sure the doors themselves were not altered square it up pin  with some 1x2 and and assess opening make adjustments if needed reinstall ( oh shoot man what did I get myself into I should have gone T&M on this baby)

My guess is the doors can be saved. They can be a pain to adjust and nothing beats a clean install

While I would agree that a top of the line Mavin or Andersen is better on many levels it is not in everyone's budget. I think a big box door is fine when installed correctly

In Colorado that door would last 2 years.  It has no way to prevent the UV from damaging the weather seal at the meeting stile of the active/passive door. Agreed budget is big factor for most homeowners.  The particular door in the pic can be reinstalled P/L/S, but that is a bandaid.  Hinge adjustments could tighten it down perhaps, but just based on the pics I would not let my customers live with it.  Just my two cents.  Good discussion though!

I hate French doors- they are almost always leakers. Over 95% of the time only the active door gets used.  So, I recommend people take them out and put in a good quality door with one or two side-lights. If they need a larger opening I tell them to put in a 3'6" door. 

As is stated above, a good seal starts with a good installation, but even that can go bad. Around here we have clay soil and in my own backyard I've had cracks open up 2"x12" deep. Lots of older homes existing foundations can't handle that an they shift and move. Single doors have a much better chance of maintain their seal then the French. 

Another option to consider is adding an astragal.  This is a molding fastened to the outside edge of the passive door, lapping over the active door.  Run weather stripping on the inside face that contacts the active door.  This will solve both the air leakage and insect problems without having to re-hang or replace the doors.

Learn to take better pictures. Use the flash more often and focus!

Without being there and with a couple of out of focus and poorly lit photos, everyone would be taking a guess at a solution. I need to "read" the entire door before making adjustments, because there are many different tweaks that could be done, but usually when you change one thing, you affect something else.

If the door is a name brand, consider contacting their tech support. Sometimes even the best doors have missing parts or other problems. In my experience, Marvin tech support is great and Andersen is OK..

Brush weatherstrip, have used Sealeze brand on such doors, as noted, may need astragal. Brush w/s good for irregular / un-aligned openings; choice of plastic or aluminum extrusion, color & brush length.

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Profile IconScot Davidson, j jarvella and Michael joined Home Energy Pros
3 hours ago
Kaushal Bharath Raju replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Hi David & Bud, $400/sqf > $300 sqf. The latter is the minimum cost of new construction in…"
4 hours ago
David Eakin replied to Kaushal Bharath Raju's discussion Affordability & Deep Energy Upgrade/Passive House Retrofit in Berkeley, California.
"Kaushal, There was a deep energy retrofit upgrade project (to Passive House standards) in San Jose…"
6 hours ago
Kim Tanner updated an event

Beyond Residential Testing at The Energy Conservatory

May 14, 2014 to May 16, 2014
The Energy Conservatory (TEC) is hosting a Beyond Residential Testing event. In addition we are…See More
8 hours ago
Casey Gesell posted a video

Super Attic - Attic Insulation System

http://www.drenergysaver.com | 1-888-225-6260 The new Super Attic: Advanced Conversion System -- converts your attic from a vented attic into an unvented at...
8 hours ago

Casey Gesell just added their location.
(via Member Map)

10 hours ago
H.O. Electric posted a video

H.O. Services, Generator, Electrical, Plumbing, Heating, Cooling, Belmont, Lexington, Arlington, MA

H.O. Services is your residential Electric-Plumbing-Heating-Cooling Specialist. We are an electrical contracting company providing homeowners the best Electr...
11 hours ago
Jim Gunshinan's blog post was featured
11 hours ago
Luis Hernandez posted a discussion

Air Source Heat pump or mini-split efficiency

Greetings everyone!    I have a technical questions I hope I could get some feedback! I understood…See More
12 hours ago
Jim Gunshinan posted blog posts
yesterday
H.O. Electric posted a photo

about us-team

H.O. Services is your residential Electric-Plumbing-Heating-Cooling Specialist. We are an…
yesterday
H.O. Electric added a discussion to the group News & Announcements
Thumbnail

Stay Cool With Easy To Install Ductless AC System!

Stay Cool With Easy To Install Ductless AC System!   Save $300.00 Off A New AC System For A Limited…See More
yesterday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service