Hi All,

I am trying to figure out a good flow grid system to use for testing airflow in 2 to 5 ton forced air systems.

Any favorites?

Or, if you prefer a flow-hood, please tell my why.

The flow hoods I've used take up more space in my vehicle than I would like.

Thanks for your thoughts.

George

Tags: flow, hoods, tools

Views: 123

Reply to This

Replies to This Discussion

I have 3 hoods - low flow ( 10-500 CFM)  Med flow (40-1500 CFM)  high flow (50-2000CFM) Open grid  for kitchen hoods. Plus hot wire plus presser plus other testing tools.   I test the air flow 3 ways  on each major job just to make my point or so I do not mess up.    Flow hoods have been used for 70 years and there's a lot of groups to help get it right.   look at http://www.trutechtools.com ,  www.nationalcomfortinstitute.com,  www.nebb.org,  https://www.aabc.com/www.tabbcertified.org.  I hope this helps some 80% air systems do not have the air flow to keep the unit on high limit.  

Thanks Eric!

Assuming that you're mainly interested in the total air handler flow, and you have access to the filter slots, I'd suggest looking at Energy Conservatory's TrueFlow.  It's a flat plate with openings; it has adapter plates for a variety of filter slot sizes. You'll also need to drill a hole in the supply plenum (or otherwise get a pressure tap in there).

  http://www.energyconservatory.com/products/trueflow%C2%AE-air-handl...

I like the flat true flow plate when it fits-  if not the by pass is very very large.   Or if the presser is to high  its off some.   I have used 4 True flow plates  on a 2 ton spit system to find air flow.    Quick way is just use paper work that comes with the air handler ( you know the knee pad that come with the unit)  find the right unit using the right MO #  then total CFM reading the fan performance data at a constant speed chart.  to find Total SP use your blower door meter with a SP gauge both side of  motor, 3 of 10 will be off with high turbulence.  Have some fun with it and write about it I will be looking for your comments. 

If you wanted more information on the TrueFlow plate, the manufacturer is offering a webinar on it today: https://events-na11.adobeconnect.com/content/connect/c1/1097690081/...

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Steve Waclo posted a discussion

Underperforming? Energy Efficiency of HVAC Equipment Suffers Due to Poor Installation

Hello all,A search of the site seems to indicate this recently published study from NIST has not…See More
2 hours ago
Steve Waclo joined Allison A. Bailes III's group
Thumbnail

HVAC

HVAC design, Manuals J, S, T, & D, Duct leakage, Air flow, ENERGY STAR new home requirements,…See More
2 hours ago
Bob Blanchette posted a discussion

Dual Fuel Systems, at what point do they make sense?

Heat Pump with furnace backup. These make no sense in our area with local NG rates, but they do…See More
16 hours ago
Bob Blanchette joined Hal Skinner's group
Thumbnail

The RCC Classroom (Radiant Control Coatings)

A group where energy professionals can learn about all the different energy saving aspects of…See More
16 hours ago
Shashank Kirloskar posted a blog post

Important Facts about Solar Energy

“I’d put my money on the sun and solar energy. What a source of power! I hope we don’t have to wait…See More
Thursday
reflintorm replied to Dennis McCarthy's discussion Solid state lighting - saves lives- and it improves life .
"In my observation, In most of the lightning appliances led bulbs are used because of their…"
Thursday
Chad Mcaulife posted photos
Wednesday
Bob Blanchette commented on Jeremy Begley's blog post The Home Envelope : Does it Really Matter in a Heat Loss Calculation
"Infiltration makes a HUGE difference. Look at the heat loads on a windy day vs. a calm one. On a…"
Wednesday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service