I've been doing HP assessments for 12 years, but find myself a little limited in my knowledge of this issue.

Here's the scenario: I do an initial assessment where I find a 7-year old NG water heater with 1500 ppm undiluted CO. The homeowner brings in his plumber to "fix" it. The plumber, who doesn't own a CO monitor, cleans the burner and air intake grill, and proclaims it good. After work is done on the home, I re-test and find the CO to be even higher this time, and the draft weak.

What typically can be done to a fairly new water heater to fix the CO problem? The gas/air ratio must be out of wack, I'm thinking. Is it usually corrected by replacing the gas control valve?

The homeowner is left hanging, the plumber is without a clue and me telling him it needs to be corrected. I would recommend a different plumber, but I want to find out what a knowledgeable individual would typically do to correct this, short of replacing it. One thing I know is I need to align with a knowledgeable person to address this in the future.

John Shillito

Tags: CO, heater, plumber, water

Views: 518

Reply to This

Replies to This Discussion

I have to agree with Kurt. 2000 ppm is exceedingly high. I have tested hundreds of hot water heater (NG, Oil) and mostly they come in around 16 ppm. There is clearly something wrong and we all know that a gas hot water draft can easily be compromised. 

hey thanks for the links. Very informative on FVIR units

Hello John (and everyone else in the forum),

I'm a new visitor at this forum and it this is my first post. I look forward to more sharing and learning in the future.

The first condition that I would investigate the "weak draft". Is the flame lazy too? Is the equipment in place the same as what the flue was originally designed for?

I find the best place to contact when at a loss is the manufacturer's technical support.

Steve

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Hal Skinner replied to Richard Beyer's discussion Media Reports Spray Polyurethane Foam Insulation spontaneously combusted a $5M Connecticut Home... "The Conclusion"
""fire origin had overheated and ignited during the curing process." No attorney…"
13 hours ago
John Nicholas replied to Sean Lintow Sr's discussion Blower Doors & Methods Used in the group Best Practices (Residential)
"Different houses, different problems, different approaches. A multipoint gives you a slope. The…"
22 hours ago
John Nicholas replied to Sean Lintow Sr's discussion Blower Doors & Methods Used in the group Best Practices (Residential)
"Bud,  I pretty much agree with Sean's points.  Given the time it takes to set up the…"
22 hours ago
Bud Poll replied to Sean Lintow Sr's discussion Blower Doors & Methods Used in the group Best Practices (Residential)
"A multi-point will take longer, but what will it do for the home owner?  Will it change the…"
yesterday
Sean Lintow Sr replied to Sean Lintow Sr's discussion Blower Doors & Methods Used in the group Best Practices (Residential)
"Hmmm good question - personally for air-leakage I would go with multi-point, preferably run from…"
yesterday
Richard Beyer posted a discussion

Media Reports Spray Polyurethane Foam Insulation spontaneously combusted a $5M Connecticut Home... "The Conclusion"

OFFICE OF THE FIRE MARSHAL1212 WHITTEMORE RDMIDDLEBURY, CONNECTICUT Fire Investigation Report –…See More
yesterday
Profile IconDavid Hepinstall and Matthew joined Home Energy Pros
yesterday
Steve Leombruno posted a blog post

Static power energy box

Just wondering if You've heard of this Static power energy box that boasts energy consumption…See More
yesterday

© 2015   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service