"When I am asked to fix this home. I start with a Heat Loss and gain, blower door IR sq…"
Fix this leakage?
What sort of leakage reduction could I expect if I try to plug all these tiny gaps?
This is a typical cathedral ceiling around these parts, 2x6 tongue and groove over 4x beams. In this image we're looking at a big valley rafter running diagonally in front, with a beam in the background at right. There are a couple of can lights and a couple of skylights in there too. This is after about 30 minutes with the door running and a 20 degree delta T. All of the beams have strips of trim, about 3/8" x 1", nailed on with brads. Lots of air comes out from behind that trim, where boards end. Relatively little comes out in the field, apparently because there's poly sheeting behind the 2x6.
It would be possible to pull each piece of trim with a flat bar, pull the nails, caulk behind it, drill a hole into each joint, inject more caulk in hopes of sealing the tongue/groove, and renail the trim. Some of this stuff is 16 feet in the air above the grand piano, really hard to get at.
Ever done a test-in, test-out on leakage like this? Did you get big results? This house is well around 2 CFM50 per square foot, so it needs a major reduction.
Views: 155
- Attachments:
-
-
car decking.jpg, 44 KB
-
Replies to This Discussion
-
Permalink Reply by Craig Bird on -
I have sealed this before. IMO, it would be easier to run two beads of caulk on each side of trim rather than removing the trim piece. Unfortunately I didn't individually test the measure when I did the job, so I am not sure how much that contributed.
-
Permalink Reply by Bud Poll on -
Hi David,
I've worked above expensive furnishings and either everything has to be moved or protected. Drop that flat bar and no one is going to be happy. Thus, I might consider the back door approach. Do everything else and what is left is some base amount plus that ceiling. If you can isolate that room in any way, some zone pressure readings might help identify how much is coming from where. Again, even if you can't read that space, maybe you can read others. Divide and conquer.
Bud
Home Energy Pros
Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy, under the American Recovery and Reinvestment Act) and brought to you in partnership with Home Energy magazine.
Latest Activity
Bud Poll replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"This is a topic I have discussed many times, but unfortunately cost is all too often the deciding…"
Sean Lintow Sr replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"If you can't talk them into replacing with IC rated...
Look into Tenmat - those are designed…"
Bachi Brunato posted a discussionBoxing and Insulating Around Non-ICAT Cans
I have a client with 16) 4" halogen recessed light fixtures in the attic.I'd like to cover the cans…See More
Dennis Heidner replied to Patrick Michaelyan's discussion Hot Upper Stories"Could you have them make a simple two line graph of the outside temperature, noting sun/clouds,…"
Bob Blanchette replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"You make some valid points, especially with the base rate charges. Increasing the base rate instead…"
Bob Blanchette replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"Amen, make energy show it's true cost instead of subsidizing it.
We have some of the lowest…"
Dennis Heidner replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"The press report really doesn't give enough information to clearly answer why they are…"
Edward Foskey commented on Edward Foskey's blog post Preparing to Update the Heat Pump"Gustavo,
Thanks for the input. I agree with you in that I will be waiting till my system's…"
Gustavo Melo commented on Edward Foskey's blog post Preparing to Update the Heat Pump"Any system that is out of warranty is really a coin toss as to whether it is financially better to…"
© 2013 Created by Lawrence Berkeley National Laboratory.
