Selecting a Water Heater
I am looking at updating the heating and water heating systems in a rental home I recently…See More
Doggy Doors...What to do?
I did an audit yesterday and found out that a single doggy door was responsible for 1,300 CFM50 of air leakage (in an already-leaky house...total leakage of 5,300 CFM50 and only 2,200 square feet of conditioned floor area).
So, what to do about this doggy door? I could spent some time thinking of a clever way to address this, or do some research online, but I thought of y'all first, as the preeminent professionals.
Any advice?
Thanks,
Patrick
Views: 360
Replies to This Discussion
-
Permalink Reply by Sean Lintow Sr on -
Replace it with one that has two doors (one on each side) & magnets - they work great
I can't recall the brand but the last few I got were at Home Depot & I think I even saw them at Lowe's
-
Permalink Reply by Curt Kinder on -
Most pet flaps have some sort of positive closure, magnet or similar, and for the most part they work OK, although some air works its way around the flap's perimeter.
What I think happened here is that the blower door test pressure, which far exceeds natural pressure, overwhelmed the flap's magnet and it swung open, allowing an extra 1300 CFM. That should not occur under normal, non-blower-door test conditions.
-
Permalink Reply by Sean Lintow Sr on
-
Let me call Bull - if the blower door could pull it open, that means the wind will easily blow it open as it wasn't able to resist one pound of pressure (PSF) --- for more see Pascals & Pressure
Either the magnet is shot, it is filthy, or the unit is worthless, which is one reason why I like the double flap system
-
Permalink Reply by Patrick Michaelyan on -
I appreciate the frankness Sean (I really do).
Let me look into this flap again, and maybe these folks are looking at the POS series pet flap.
-
Permalink Reply by Curt Kinder on
-
The blower door test pressure of 50 Pa is roughly equivalent to a 20 mph wind, which is quite uncommon in most areas
-
Permalink Reply by Bob Blanchette on -
Unless you live in Oklahoma.
-
Permalink Reply by Patrick Michaelyan on
-
Thanks Curt.
I have to look at this flap again. It appeared to fit by friction.
-
Permalink Reply by peter chang on
-
Locating pet doors on a relatively sheltered wall of the house could help. I've been designing a two door doggie airlock in my head. It would be disguised as a bench (or banco in my neck of the woods), be heavily insulated, and vented to the exterior to disperse pulses of wind back to the outside of the house. If the vent could exhaust around a corner from the exterior flap that would be best, and it should have some kind of a flapper to reduce air coming in it. Or build the whole thing on the outside as a tunnel with exterior door at the end and vents both sides.
-
Permalink Reply by Bob Blanchette on
-
Locating Doggie Doors on South or East walls helps a lot.
-
Permalink Reply by Glen Gallo on -
worry more about the other 4000 cfm
the air coming from the dog door is fresh air
Where is the other 4000 cfm coming from?
S
-
Permalink Reply by Ron Jones on -
I recently had a similar situation, only the doggy door was big enough for an adolescent to crawl through. When I told my client she should consider replacing the door, she waxed nostalgic about the happy times when her dog and children would chase each other through the door. She made it clear she'd never replace the thing. I still haven't done any work for her.
-
Permalink Reply by Troy Spindler on -
Another trick I've seen is to dedicate the bottom half of a cabinet as a vestibule/mud-room with a second air-lock flapper like Peter suggests. Obviously you'ed need to design some people access to clean it out occasionally, but I agree with Glen re. the other 4000 cfm.
Home Energy Pros
Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy, under the American Recovery and Reinvestment Act) and brought to you in partnership with Home Energy magazine.
Latest Activity
Eric Kjelshus replied to Patrick Michaelyan's discussion Hot Upper Stories"When I am asked to fix this home. I start with a Heat Loss and gain, blower door IR sq…"
Bud Poll replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"This is a topic I have discussed many times, but unfortunately cost is all too often the deciding…"
Sean Lintow Sr replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"If you can't talk them into replacing with IC rated...
Look into Tenmat - those are designed…"
Bachi Brunato posted a discussionBoxing and Insulating Around Non-ICAT Cans
I have a client with 16) 4" halogen recessed light fixtures in the attic.I'd like to cover the cans…See More
Dennis Heidner replied to Patrick Michaelyan's discussion Hot Upper Stories"Could you have them make a simple two line graph of the outside temperature, noting sun/clouds,…"
Bob Blanchette replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"You make some valid points, especially with the base rate charges. Increasing the base rate instead…"
Bob Blanchette replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"Amen, make energy show it's true cost instead of subsidizing it.
We have some of the lowest…"
Dennis Heidner replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"The press report really doesn't give enough information to clearly answer why they are…"
Edward Foskey commented on Edward Foskey's blog post Preparing to Update the Heat Pump"Gustavo,
Thanks for the input. I agree with you in that I will be waiting till my system's…"
© 2013 Created by Lawrence Berkeley National Laboratory.
