Does anyone have any experience with an Owens Corning product called "Energy Complete" ?

I am interested in any comments about this product, pros and cons.
Does this product have a future as a hybrid insulating system for new construction, or is it to expensive to compete with a caulk gun or other methods?
Thanks
Mark

Views: 2593

Reply to This

Replies to This Discussion

Robert,

The OC energycomplete can not be sprayed with any paint sprayer. Its a 2 part foam 4to 1 it needs 2 pumps one is bigger then other in order to get correct ration. It also has a special gun. The Knauf Ecoseal you can use a paint sprayer they do recommend specific sprayers since the psi has to be quite high.

Knauf has a competing product called EcoSeal - http://bit.ly/lWYOZT

I know a contractor who just started using this.  It goes on with an airless sprayer.  The homes he has installed it in haven't even been completed yet.  I will get more info from him re pricing, etc.

Hey Silas,

 

thanks for the link.  Please keep me advised as more information from that contractor develops.

The product looks interesting.

Mark

I am also a certified installer of the energy Complete System based out of St. Louis.  Like many other s have said this system i great for minimizing the unwanted air flow into a home and through the insulation itself.  

Very recently Owens Corning has released a new tip for the systems spray gun that reduces wasted product by 50%. The new BEADED EXTRUSION tip allows the product to go only where it is intended to both air seal and still create the same air gasket effect as with the previous three inch band.

Owens Corning has been great with continuing to develop the system.

I spoke with a builder who has tried both the Owens product and the Knauf product.  

They quit using Owen. It sprays on and bubbles up a little. He couldnt get a good surface for the drywall to sit on. I cant remember all the particulars but he was not satisfied. It is not recommended for use with cellulose.

The builder switched to the Knauf and his mock up showed very neat crisp lines. along double studs or top plates they we tooled smooth with the face of the wood so the drywall would sit flush. 

Both Owens and Knauf have videos on their sites.

I can agree that the Owens Corning product can easily be applied too thick and create a problem for the drywallers but that problem is all in the installer not with the product.  Form personal experience it takes a few tries to get good at the application.  We actually used it to air seal a retrofit attic twice in order to practice getting the correct thickness.  Once we had that down we have not had any complaints from new construction jobs.

Did you happen to perform a blower door on the retrofit application? How did it stick in a dusty attic? This is what I am most interested in. I am wondering how it performs in retro environment. I can get the Knauf Eco-Seal at a reasonable price and already have spray equipment that is sufficient. I want to start using it to air seal attics in retro. Two part foam is just too expensive for air sealing. I can my material costs on half on a full attic air seal.

the EC foam is not the ideal product to use in Retro fit attics... we used it a few times for the simple reason of we needed to learn the operation and application of the product before it really mattered.  In an attic covered with insulation it did not matter nearly as much how pretty the application was.  the best thing that i have found to air seal and attic is simple canned spray foam. It is light weight, portable and much less expensive to use than any machine.

I wonder about adhesion-and life cycle-as well; that is compared to the "foam".

Chemically, urethanes perform much better in terms of adhesion and movement; and therefore, have a longer life compared to latex. 

RSS

Featured Forum Discussions

Too many BTU's. Too much horsepower?

Started by Steve in General Forum. Last reply by Eric Kjelshus on Saturday. 4 Replies

Stack/wind pressure and flow networks.

Started by Daniel James Grundy in Training. Last reply by Daniel James Grundy Mar 23. 5 Replies

BDT with vermiculite in hollow CMU walls?

Started by Brad Cook in General Forum. Last reply by John Nicholas Mar 23. 2 Replies

Videos

  • Add Videos
  • View All

Latest Activity

Sy Richardson posted a video

Energy Efficient Roofing & 200 MPH Wind Rated

EternaTile delivers the easiest roof to install while delivering energy efficiency, aesthetics and up to 200 MPH sustained wind resistance. Watch how easy it is to install an EternaTile roof.
44 minutes ago
Jacob Corvidae commented on Home Energy Magazine's blog post The Elephant in the Room
"Great story, Jim (and Kara).  For anyone interested in training on engaging with…"
1 hour ago
Tom Phillips commented on Home Energy Magazine's blog post The Elephant in the Room
"Great reminder! How do we get more contractors to visit their legislators? Related info from state…"
2 hours ago
Tom Phillips liked Home Energy Magazine's blog post The Elephant in the Room
3 hours ago
Jose Macho replied to Rob Madden's discussion Energy auditing as a stand-alone business model...
"Energy auditing as a stand alone business is not a sustainable business model. The biggest factor…"
3 hours ago
tedkidd replied to Rob Madden's discussion Energy auditing as a stand-alone business model...
"Oh, we are also finding EVERY effort towards radical transparency accelerates achievement of trust…"
3 hours ago
tedkidd replied to Rob Madden's discussion Energy auditing as a stand-alone business model...
"We have a stand alone model that is working, but your definitions need clarification. Do you mean a…"
3 hours ago
Home Energy Magazine's video was featured

Sneak Peek at U.S. Department of Energy Solar Decathlon 2017

Get a sneak peek at the U.S. Department of Energy Solar Decathlon team house renderings. The competition takes place October 5-9 and 12-15, 2017 in Denver, CO
4 hours ago

Home Energy Pros

Welcome to Home Energy Pros – the unique digital community by and for those who work in the home energy performance arena.

Home Energy Pros was founded by the developers of Home Energy Saver Pro (supported by the U.S. Department of Energy) and brought to you in partnership with Home Energy magazine.  Home Energy Pros is sponsored by the Better Buildings Residential Network. Please honor our Guidelines

© 2017   Created by Lawrence Berkeley National Laboratory.   Powered by

Badges  |  Report an Issue  |  Terms of Service