Greetings everyone! 

   I was hoping I could get some feedback with a building I am working on. The existing concrete was a 3 inch "homeowner special", so the plan is to set 2 inches of rigid foam, tubing for radiant heat, and four inches of new pour concrete.

1.) Do I need anything between the insulation and the existing concrete?

2.) The radiant pipes have ties to attach to the iron rods for the concrete, so I can only imagine that the metal goes first, then the radiant...

3.) How do I protect the rigid foam from damage from walking on it to do the other steps?

4.) Does the rigid foam boards needs to be taped between each other and to the end of the block?

This is a very exciting project and your feedback is greatly appreciated, 

    Luis

Tags: board, concrete, floor, foam, heat, installation, insulation, radiant

Views: 157

Reply to This

Replies to This Discussion

What is the issues with the "homeowner special" concrete - wavy, falling apart, or... That can easily change some answers depending on the severity 

#1 - generally not needed, though sometimes you might need a floor leveler, maybe even a crack/moisture isolation membrane

#2 - Personally I like having the radiant around the halfway mark in the slab with the metal though many simply attach it directly to the foam like is shown here http://blog.sls-construction.com/2012/common-sense-building-radiant...

#3 - use the proper foam & it can handle it - should be a high density closed cell foam

#4 - that is a very good idea

One last tip - make sure you have the pex lines pressurized while you are doing this and check them as you go - last thing you want to do is find out you have a leak after the concrete is set, while messy it is easier to fix now then later

Not sure if this would have any bearing on your project at all. Thought I would mention it though.
When we apply our coating on new concrete walls or new stucco, we always have to test the Ph level first. It must be no higher than 4, we prefer 3 or below. With concrete or stuccvo that is 5-yearsold or older, rarely an issue. Less than 5, many times an issue. It causes major bonding problems.
Again, not sure if a high Ph level concrete would cause issues with your foam or not. Possibly???
Some paint companies make a primer for high Ph surfaces. Might be a good thing to look into. Will a high Ph level concrete eat the foam??? I dont know, thats why I'm bringing it up.

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Sean Lintow Sr replied to Tony Rigdon's discussion Placement of 5/8" firewall, over or under foam board insulation?
"I am pretty sure he is talking about using commercial drywall designed for this type of purpose and…"
6 minutes ago
Hal Skinner replied to Tony Rigdon's discussion Placement of 5/8" firewall, over or under foam board insulation?
"Found an article that might help …"
8 hours ago
Bud Poll replied to Tony Rigdon's discussion Placement of 5/8" firewall, over or under foam board insulation?
"Hi Tony, what/where is your climate?  Also, how is the rest of the wall constructed? Adding…"
9 hours ago
Sean Lintow Sr replied to Tony Rigdon's discussion Placement of 5/8" firewall, over or under foam board insulation?
"contact the local AHJ for sure - but for "fire" reasons it should be on the outside…"
11 hours ago
Tony Rigdon posted a discussion

Placement of 5/8" firewall, over or under foam board insulation?

I'm adding onto my personal residence and since the house is within five feet of the property line,…See More
12 hours ago
Hal Skinner replied to Hal Skinner's discussion Rooftop A/C units and exposed ductwork in the group The RCC Classroom (Radiant Control Coatings)
"Hi Tom.   As far as media advertising goes for the good RCCs, it really doesnt work well at…"
14 hours ago
Sean Lintow Sr commented on Chris Laumer-Giddens's blog post Mini-Split Heat Pumps are Quirky, Especially their Capacity
"Quick question Chris - the set & forget (for temperature setbacks) is that with any or just…"
16 hours ago
Martin Smith joined Hal Skinner's group
Thumbnail

The RCC Classroom (Radiant Control Coatings)

A group where energy professionals can learn about all the different energy saving aspects of…See More
18 hours ago

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service