http://greendreamgroup.libsyn.com/this-house-sucks-but-not-very-har...

Check out this interview with brilliant scientist Brett Singer (seriously, he's a genius) from Lawrence Berkeley National Laboratory on our misconception about worst case CAZ Depressurization testing.

Tags: bpi, brett, case, caz, podcast, singer, testing, worst

Views: 1092

Reply to This

Replies to This Discussion

Even when gas stoves DO have exhaust fans they capture a small % of the combustion products. Note when a boiling pot is on the outside burners, most of the steam bypasses the exhaust hood. Inside burners get more of the exhaust. Even with 250 CFM the face velocity is way to small to capture all that much. 

solution - stoves need to be enclosed on three sides. NO one makes a stove like this but they should. This will more than double the face velocity an improve capture. Stainless side panels would do it and also eliminate splattering on adjacent counter tops. 

Good point. Now, assuming all of us here agreed, whom do you think we will win over first:
Appliance manufacturers or my wife?

Decades of experience in the Culinary realm give me a slightly different perspective.  It is the capture area of the hood that is of significance.  Installing sides will never go over, but if the hood were required to extend some predetermined amount beyond the cook surface and coupled with an appropriately sized fan motor, I believe the dynamics would fall into an acceptable range.

Hi Jim, just to add to your example from another perspective, a capture hood should also be more than a flat surface with an exhaust hole in the middle and skirting around it.  Take for example the fireplace industry that has to produce a draft without the fan.  By tapering the combustion chamber up to the flue there is a gradual acceleration of the air flow and less turbulence.  I suspect a little more air flow engineering as opposed to aesthetics would add to the effectiveness of hood design.

We must remember that the fan is not pulling the air from above the cooking surface up into the exhaust, just creating a low pressure zone in the vent so that the surrounding higher pressure can push all of that air into the little hole (just like a fireplace).

Bud

Actually engineering the flow would make sense. Maybe they need to attach the hood to the pot lid; now there is totally new paradigm.  Air jets blowing upwards around the edge of the cooktop would help also. After all that, there is still a need for some reasonable velocity to contain the products of combustion on the gas stove, the steam and smoke.  Apart from adding more flow, we haven't progressed at all in kitchen exhaust. 

Lizzy bought one of those NuWave induction stoves.  I've always hated electric and loved gas.  

I guess I have bias against induction that I wasn't aware of because even though there are all types of reviews raving about induction, experiencing it in person left me shocked.  (And I try to be open to having my schemas disrupted!)

In my mind cooking with gas is done.  If you haven't tried induction cooking, try it.  If you have tried it, and see any reasonable argument FOR gas, I'd be interested to hear it. 

Very interesting. Brett did a good job of explaining complicated subject and boiling down (pun intended)  points.

my favorite was "If you are going to do test that is going predict an unlikely event will happen then you need to do allot of monitoring to see if this event will happen"

I do not think we will see any changes anytime soon for CAZ but the podcast was a good refresher on the dangers of the gas stove top that I can take forward. I am glad that cfm in still equals cfm out

It also brings forward to me the need for mechanical ventilation. Many problems can be eliminated through dilution.  A good balanced ventilation system designed for the applicable climate is still one of the best things we can recommend for any home.

Good stuff

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Hal Skinner replied to Richard Beyer's discussion Spontaneous Combustion and Flash Fire regarding Spray Foam Insulation
"Richard, here is something else that might be pertinent. In my hundreds of conversations with our…"
6 hours ago
Trip posted a discussion

Starting a Home Weatherization Business. Considering it...

I am considering starting a home weatherization business. (I live in Southeast Alabama)  Currently…See More
7 hours ago
Jim Gunshinan commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"To all, one thing I don't lack is advice from the experts! Thanks for the input, challenges,…"
8 hours ago
tedkidd commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"Jim, I'm glad you are open, that's great!  We all learn best when we are open! The…"
8 hours ago
David Eakin commented on Jim Gunshinan's blog post My Energy Upgrade California—The Numbers Are In
"Jim, Well, as the editor of Home Energy you should already know that the order of remediation is…"
8 hours ago
Greg Labbe posted a blog post

Technical Tape Desecration

Lets face it – building science is pushing the performance of adhesive tapes to a new levels and…See More
10 hours ago
Stacy Hunt posted an event

High Performance Enclosure Strategies: Part II, New Construction at Online

August 13, 2014 from 1pm to 2:30pm
Please join the Building America Program for our free webinar: High Performance Enclosure…See More
12 hours ago
Richard Beyer replied to Howard Katzman's discussion UV lights on filters
"Howard, There are numerous manufacturer's who swear these systems work and then you have the…"
21 hours ago
Christopher Morin posted a blog post

How do You Test a TXV?

  Thermostatic Expansion Valves (TEV or TXV), one of the most popular metering devices for…See More
yesterday
Howard Katzman posted a discussion

UV lights on filters

I recently saw UV bulb installations in 2 HVAC systems in a home. Each system had the Lennox…See More
yesterday
Don Fitchett joined Michael Stuart's group
Thumbnail

INFRARED THERMOGRAPHY USERS

This group is dedicated to knowledge sharing and discussion of infrared thermography for building…See More
yesterday
Don Fitchett commented on Diane Chojnowski's group Pinterest
"While most of our (BIN95.com) energy post and boards are industrial related, there are crossovers…"
yesterday

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service