"You note overheating on the south side (naturally.) Assuming the typical roof overhang of…"
Any Experience with Radiant Barrier Bubble Wrap
I wanted to know if anyone had any experiences using the bubble wrap w/ the double sided radiant barrier.
I had a weird experience thanks to a fire pit, my Brother-in-Law, and a few beers. My Brother-in-Law made a make shift pot holder looking glove and held it about 8" away from a pile of extremely hot embers. After nearly a minute the glove started to smoke because the exterior nearest the fire was starting to melt. Despite this, he said the inside never got that hot.
What I am figuring is that, if this material works this well with such extreme temperatures, why wouldn't it be useful in a knee wall area? It would be a lot easier to install than rigid foam board and much easier to squeeze through a small access hole.
What do you guys think? Do you have experience using this material? (Keep in mind I live in Atlanta, GA, not New England). Thanks!
Tags: Insulation, bubble, heat, knee, transfer, walls, wrap
Views: 340
Replies to This Discussion
-
Permalink Reply by Ben Stallings on -
Remember, a radiant barrier only reflects radiant heat. The fire test your brother in law did was the ideal test for that material, since essentially all the heat was radiant, but in an attic situation that's not the case. For the radiant barrier to work, there has to be an air space between the barrier and any other objects (to rule out conduction), and its surface has to remain clean and shiny (no dust collection). So would it help in a kneewall area? Maybe a little, but not as a replacement for insulation.
-
Permalink Reply by Jon LaMonte on -
I get your point, but I am talking about using it in addition to the existing insulation. The most common treatment here for knee wall problems is to seal the penetrations from the attic side of the wall, push the batts (usually R-13 here) back into place and then attach Thermax sheathing with a radiant barrier to the studs over the batts and seal the seams. Sometimes the construction, access, and penetrations make using a rigid foam board product very difficult to use. The bubble wrap radiant barrier seems to be a good alternative.
-
Permalink Reply by Ben Stallings on
-
Installed in that location -- over the fiberglass batts -- I would be concerned about condensation on the bottom surface wicking into the fiberglass and creating mold habitat. I'd also be concerned that dust would accumulate on the top surface and make the radiant properties useless.
Has this stuff been in use long enough to be able to check in on an installation that's 5 or 10 years old to see how it's holding up?
-
Permalink Reply by David Eakin on
-
Jon,
I'm guessing that the foil/bubble wrap will provide a real good air seal if installed properly (like every other air seal material) but will be much more costly than poly wrap and not provide anywhere near the insulation of EPS or XPS board. I've seen no independent testing of these products to verify their claimed "R" values. Knee walls are always a pain; almost makes you want to rip out the walls to re-do everything.
-
Permalink Reply by Jon LaMonte on
-
You can say that again.
-
Permalink Reply by A. Tamasin Sterner on -
We see Reflectix used behind knee walls all the time. It is the air barrier to prevent windwashing, and meets code for fiberglass batt covering.
-
Permalink Reply by Guy DuBois on -
You should put a link to Reflectix in your post. I haven't heard of it.
Home Energy Pros
Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy, under the American Recovery and Reinvestment Act) and brought to you in partnership with Home Energy magazine.
Latest Activity
Patrick Michaelyan replied to Patrick Michaelyan's discussion Hot Upper Stories"Thanks a lot Ed. And thanks to all who have added their two cents.
I think I know where to take…"
Ed Minch replied to Patrick Michaelyan's discussion Hot Upper Stories"We have successfully treated this same problem in perhaps 1000 of this same house in the…"
Craig Savage commented on Craig Savage's video
What is a Heat Pump Water Heater
"Hello Tom
We are working with A.O. Smith, GE and Stiebel Eltron on a Building America task to…"
Tom Delconte commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Craig: I was serious, since my propane price jumped from .98 to 1.85! according to everyone the GE…"
Ben Jacobs replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"I think that government support for good ideas results in major benefits over the long haul.
Please…"
Craig Savage commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Hello Tom
Not sure if you are being sarcastic, but a serious answer would be that GE is selling…"
Tom Delconte commented on Craig Savage's videoWhat is a Heat Pump Water Heater
"Craig: do you have a diagram of one that will run longer than one year? They don't really seem…"
Cory Chovanec replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"All good points brought up. My advice is not to leave the lights. When you said halogen I think…"
Jon Haehnel replied to Jose Macho's discussion Why Are Energy-Saving Home Inprovements Down??"The first 2 answers by Tom and Sean jive with my thinking and experience. Thank you Don for…"
Tom Smith replied to Patrick Michaelyan's discussion Hot Upper Stories"The most bang for your buck will come from airsealing the attic plane and sealing the…"
John Rising replied to Bachi Brunato's discussion Boxing and Insulating Around Non-ICAT Cans"Hi Bachi,
We have done many projects where we have installed boxes around recessed lights to…"
© 2013 Created by Lawrence Berkeley National Laboratory.
