Bob Sullivan's Discussions (12)

Discussions Replied To (11) Replies Latest Activity

"InsulSmart is a two-part aminoplast interior foam insulation offered by cfiFOAM, Inc…"

Bob Sullivan replied Nov 1, 2013 to Air sampling low pressure two part foam

4 Nov 1, 2013
Reply by Bob Sullivan

"Aminoplast injection foam is available today that greatly surpasses the old technolo…"

Bob Sullivan replied Nov 8, 2012 to Urea Formaldehyde Foam Insulation (UFFI)

10 Feb 13
Reply by Thomas Varney

"Whatever R-value loss occur due to fiberglass compression is partially offset by an…"

Bob Sullivan replied Sep 2, 2011 to Slow cure foam injected behind fiberglass in walls?

23 Sep 2, 2011
Reply by Bob Sullivan

"John,   Across the insulation industry, most manufacturers disclose R-values at 75 F…"

Bob Sullivan replied Aug 23, 2011 to Slow cure foam injected behind fiberglass in walls?

23 Sep 2, 2011
Reply by Bob Sullivan

"John,   A nice thing about injection foams is that they more easily flow around pipe…"

Bob Sullivan replied Aug 23, 2011 to Slow cure foam injected behind fiberglass in walls?

23 Sep 2, 2011
Reply by Bob Sullivan

"John, InsulSmart and Tripolymer 105 install similarly. Current and past Tripolymer 1…"

Bob Sullivan replied Aug 23, 2011 to Slow cure foam injected behind fiberglass in walls?

23 Sep 2, 2011
Reply by Bob Sullivan

"Pat, I'll answer your questions one by one, as follows:   Is there some recommendati…"

Bob Sullivan replied Aug 23, 2011 to Slow cure foam injected behind fiberglass in walls?

23 Sep 2, 2011
Reply by Bob Sullivan

"Brad,   Here's all three MSDS for InsulSmart MH.   Bob"

Bob Sullivan replied Aug 19, 2011 to Slow cure foam injected behind fiberglass in walls?

23 Sep 2, 2011
Reply by Bob Sullivan

"Brad,   Over time, DP cellulose has earned a loyal following of advocates; however,…"

Bob Sullivan replied Aug 19, 2011 to Slow cure foam injected behind fiberglass in walls?

23 Sep 2, 2011
Reply by Bob Sullivan

"Brad, We're the manufacturer. All injection foams are considered open-cell foams. We…"

Bob Sullivan replied Aug 18, 2011 to Slow cure foam injected behind fiberglass in walls?

23 Sep 2, 2011
Reply by Bob Sullivan

RSS

Home Energy Pros

Home Energy Pros was founded by the developers of Home Energy Saver Pro (sponsored by the U.S. Department of Energy,) and brought to you in partnership with Home Energy magazine.

Latest Activity

Energy Center University posted an event

Better Buildings: Better Business Conferences at Crowne Plaza Chicago O'Hare Hotel & Conference Center and Kalahari Resort and Convention Center

February 26, 2015 to March 13, 2015
Better Buildings: Better Business ConferencesFebruary 26−27, 2015 │ Rosemont, ILMarch 11−13, 2015 │…See More
13 hours ago
Kris Grube added a discussion to the group Job Board
Thumbnail

Good Energy Retrofit, Portland, Or. Hiring Home Performance Salesperson.

Good Energy Retrofit is a small and focused, woman owned and operated, specialty residential…See More
17 hours ago
Benjamin Gromicko posted events
18 hours ago
Nate Adams joined Diane Chojnowski's group
Thumbnail

Hall of Shame

In this group, members share an array of images from the field, showing the kinds of issues…See More
18 hours ago
tedkidd commented on Diane Chojnowski's group Hall of Shame
"Give this thread a bump - here's my "bad" album and some of the…"
19 hours ago
Eric Kjelshus commented on Adam Swain's blog post Top Worst Crawl Space Insulation Ideas
"6) Radiant barrier- under the gravel is just a barrier but with holes each square inch its not a…"
19 hours ago
tedkidd replied to Luis Hernandez's discussion Distribution Efficiency and heating safety factor in TREAT in the group TREAT Software
"It is very common to find equipment grossly oversized. I mean 1.5 - 2x Manual J and 2-3x the size…"
19 hours ago
tedkidd replied to Luis Hernandez's discussion Basic Heat loss information in the group TREAT Software
"Luis,  Click "selected reports, energy savings and use, design heating and cooling…"
19 hours ago

© 2014   Created by Lawrence Berkeley National Laboratory.

Badges  |  Report an Issue  |  Terms of Service